Ricoh PCU10 Скачать руководство пользователя страница 84

Страница: 84 / 195

2.6.2 Transfer and separation mechanism

The transfer and separation corona unit is on the

transport unit.
The transfer entrance guide mylar at the transfer corona

inlet holds the paper against the photoconductor to

eliminate transfer blurring of the leading and trailing

edges of the copy.
Paper separates due to paper rigidity after the negative

charge is removed from the paper by the separation

corona. The OPC belt turns at a sharp angle and this

helps the paper to separate from the photoconductor.
The transfer is output at a constant current and

separation is output at a constant voltage from the

transfer/separation power pack.
Transfer output:
DC (--)140

A. [(--)5.7KV]

Separation output:
AC200

A, DC(+)25

A. [AC6.3KV, DC(+)0.8KV]

2.6.3 Transport belt drive mechanism

The transport belts are driven by the main motor through

the vertical transport drive (see chart).

Paper

Separation corona wire

Tracking rollers

Guide mylar adjusting screw

Transfer

entrance

guide mylar

OPC

Separation corona wire

Antivibration ring

T/S corona

power pack

Transfer corona wire

Transfer

corona

Relay drive pulley

Main transport

drive belt

Main motor

Vertical transport

drive belt

Joint pulley

Transport belt

drive gear

Main motor

Main transport drive belt

Relay drive pulley

Joint pulley

(Vertical transport unit)

Vertical transport drive belt

Transport belt drive gear

Image Transfer and Paper Separation

1 July 1994

2-48

Содержание PCU10




































































































































































































Результаты поиска

Содержание PCU10

Отзывы:

Похожие инструкции для PCU10

Бренды по названию

Популярные бренды

Ricoh PCU10, Руководство по обучению обслуживанию

Результаты поиска

Содержание PCU10

Отзывы:

Похожие инструкции для PCU10

Бренды по названию

Популярные бренды