Ricoh PCU10 Скачать руководство пользователя страница 149

Страница: 149 / 195

Reverse section

SADF exit gate

The SADF exit gate is switched by the SADF exit gate

solenoid. When the solenoid is OFF, the gate plate is

lowered by the force of the spring to guide the original to

the reverse section.

Reverse junction gate

The reverse junction gate pawls are switched by the

reverse junction gate solenoid. When the solenoid is off,

the solenoid plunger and gate pawls are pulled down by

the spring to guide the original in the reverse section.

When the solenoid is ON, the original is guided to the

intermediate transport unit side.

Intermediate transport unit

The intermediate transport unit is lowered by sliding the

release lever. This helps the removal of jammed

originals.

SADF exit gate

SADF exit gate solenoid

Reverse

junction

pawls

Reverse junction

gate solenoid

Transport belt

Belt

tension

arm

Lock pin Lock pawl

Release lever

Intermediate

transport unit

1 July 1994

ADF

2-113

Содержание PCU10




































































































































































































Результаты поиска

Содержание PCU10

Отзывы:

Похожие инструкции для PCU10

Бренды по названию

Популярные бренды

Ricoh PCU10, Руководство по обучению обслуживанию

Результаты поиска

Содержание PCU10

Отзывы:

Похожие инструкции для PCU10

Бренды по названию

Популярные бренды