Ricoh PCU10 Скачать руководство пользователя страница 101

Страница: 101 / 195

2.9 Development

2.9.1 Main construction

Structural diagram

Construction

Three magnetic rollers are used to meet the high speed

requirements.
Two paddle wheels, a separator, and a transport auger

are used for agitation.
Negative bias voltage is applied to the development

rollers.
The toner density sensor controls the toner density. The

control condition is changed by data from the ID sensor.
The toner density sensor detects toner end condition.

The toner near-end sensor is also used to detect the

near-end condition.
There are two detecting mechanisms for the toner

cartridge replacement. One is to detect the set of the

cartridge. The other is to detect the shutter operation of

the cartridge.
An independent dc motor drives the unit.
A blower sends air to the ID sensor to prevent the

sensor from becoming dirty.

Separator

Toner density sensor

Toner cartridge

Developer auger

Small toner agitator

Main toner agitator

Toner hopper

Toner near-end sensor

Toner supply roller

Toner density control board

Toner inlet

Development unit

shutter

Paddle wheel

Development backup roller

1st development roller

2nd development roller

Backspill plate

ID sensor

Filter

Developer inlet

Opening

3rd development roller

Doctor blade

OPC belt

Development unit

Development mechanism

Developer agitator mechanism

Development bias mechanism

Toner density control and supply

mechanism

Toner near-end detection

mechanism

Toner cartridge replacement

Drive mechanism

ID sensor anti-contamination

mechanism

1 July 1994

Development

2-65

Содержание PCU10




































































































































































































Результаты поиска

Содержание PCU10

Отзывы:

Похожие инструкции для PCU10

Бренды по названию

Популярные бренды

Ricoh PCU10, Руководство по обучению обслуживанию

Результаты поиска

Содержание PCU10

Отзывы:

Похожие инструкции для PCU10

Бренды по названию

Популярные бренды