Ricoh PCU10 Скачать руководство пользователя страница 146

Страница: 146 / 195

2.14.5 Original separation and feed

Original leading edge separation

Air from the ADF blower is blown through six holes in the

air knife casing to the center of the original.
The blower keeps blowing air on the original tray from

the beginning to the end of the original feeding to

prevent double feeding of originals.

Original feed

After the originals are separated by the ADF blower, the

shutter solenoid mounted on the ADF blower is

energized by a paper feed signal from the main control

board. The bottom sheet is held against the transport

belts by the suction of the ADF blower.
Next, through the timing belt and feed magnetic clutch,

the original feed motor drives the feed rollers and

transport belts. The belts transport the original to the

feed rollers.

Blower

The air suction and air knife separation are provided by

two turbine fans on one blower.
A brushless dc servomotor with reduced wear, noise

and electrical noise is used in the ADF blower to ensure

long life and high reliability.

Shutter solenoid

The shutter solenoid controls air suction to hold the

lowest original of the stack against the transport belts.

When this solenoid is OFF, the vacuum shutter is

opened and the original is not affected by suction.
In the stack mode (the ADF mode), the originals may be

damaged by the air suction if the originals stay in the

same place for a long period. To prevent this, in the

stack mode, if the selected copy number for an original

goes over 9, the solenoid is automatically turned OFF.

The solenoid is again turned ON for the last 6 copies.

Air knife casing

ADF blower

Shutter solenoid

Original feed roller

Original feed

magnetic clutch

Original feed

motor

Joint gear

Air inlet

ADF blower

Vacuum shutter

Shutter solenoid

Suction when solenoid ON

Air suction

Air exhaust

To air knife

ADF

1 July 1994

2-110

Содержание PCU10




































































































































































































Результаты поиска

Содержание PCU10

Отзывы:

Похожие инструкции для PCU10

Бренды по названию

Популярные бренды

Ricoh PCU10, Руководство по обучению обслуживанию

Результаты поиска

Содержание PCU10

Отзывы:

Похожие инструкции для PCU10

Бренды по названию

Популярные бренды