Ricoh PCU10 Скачать руководство пользователя страница 49

Страница: 49 / 195

2.1.13 Error reset

Problem:

Paper tray up or down error at tray 1. When the tray motor rotates for about 20 seconds, no

paper volume sensor signal (tries twice).

Cause:

Poor connection, sensor failure, broken wire, motor malfunction, or motor driver board failure.

Problem:

Paper tray up or down error at tray 2. Same as 60 above.

Cause:

See 60 above.

Problem:

Paper tray up or down error at tray 3. Same as 60 above.

Cause:

See 60 above.

Problem:

Paper feed transmission error (No response from CPU for paper feed).

Problem:

Paper feed receiving error (communication error).

Cause:

Fiber cable disconnected, broken wire, or paper feed control board failure.

2.1.14 Jam detection timing

Checks for jams are done as shown in the figure (both

ON and OFF check). The display shows you the

location of the jam.

2.1.15 Troubleshooting

Problem

Possible Causes

Paper dust in the machine, especially in the cleaning unit,

makes dirty background copy.

Paper dust removal roller and mylar are not contacting properly.

Jams during copying and jam indicator A is displayed. The

leading edge of the jammed paper is near the fusing

entrance.

Paper feed sensor 2 remains OFF

Paper feed jam occurs at power ON. This cannot be reset.

Paper feed sensor 2 remains ON

Error reset detection, No. 60, 61, 62

Paper volume sensor failure (no pulse).

No size display, tray does not raise.

Paper size sensor failure

1/2

" x 14" is displayed although B4 paper is set in the tray.

Jam detected and leading edge of the paper is near the

fusing entrance.

When B4 paper was set, the back guide shifted 5 mm backwards.

Paper skews during paper feed, causing a jam. If jam

does not occur, skewed image occurs.

The side guides of the tray are not set tightly.

Horizontal

transport exit

sensor

Horizontal transport

entrance sensor

Paper feed

sensor 2

Paper feed

sensor 1

Registration sensor

1 July 1994

Paper Feed

2-13

Содержание PCU10




































































































































































































Результаты поиска

Содержание PCU10

Отзывы:

Похожие инструкции для PCU10

Бренды по названию

Популярные бренды

Ricoh PCU10, Руководство по обучению обслуживанию

Результаты поиска

Содержание PCU10

Отзывы:

Похожие инструкции для PCU10

Бренды по названию

Популярные бренды