Ricoh PCU10 Скачать руководство пользователя страница 83

Страница: 83 / 195

2.6 Image Transfer and Paper Separation

2.6.1 Main construction

Structural diagram

Construction

The flex separation system. Transfer and paper dis-

charge by the transfer and separation discharge. An mis-

feed on the transport unit error is detected by a

reflective photosensor.

The transport belts are driven by the main motor through

the vertical transport drive.

After separation paper is held against the transport belts

by the suction of the vacuum fan.

The transport release spring is used to release the trans-

port unit.

The positions of the T/S corona and transport units are

separately maintained.

Transport belt

Separation

corona wire

Transfer corona wire

Guide mylar

adjusting screw

Transfer entrance

guide mylar

Vacuum fan

Transport unit

Transfer and

separation corona unit

Transport belt

Separation sensor

Transfer and

separation power

pack

Image transfer and

paper separation

Transfer and separation

mechanism

Transport belt drive

mechanism

Transport vacuum

mechanism

Transport unit release

mechanism

Transfer/separation and

transport unit positioning

1 July 1994

Image Transfer and Paper Separation

2-47

Содержание PCU10




































































































































































































Результаты поиска

Содержание PCU10

Отзывы:

Похожие инструкции для PCU10

Бренды по названию

Популярные бренды

Ricoh PCU10, Руководство по обучению обслуживанию

Результаты поиска

Содержание PCU10

Отзывы:

Похожие инструкции для PCU10

Бренды по названию

Популярные бренды