manualshive.com logo in svg

Ricoh MPC 2800 AT-C2, Руководство по обслуживанию на месте, Страница: 663 / 856

Поделиться
Скачать
Ricoh MPC 2800 AT-C2 Скачать руководство пользователя страница 663

001 BE

-

[0 to 1023 / 0 / 1 digit/step]

002 BO

-

4693

[Black Level Read]

Displays the peak level of the black level scanning.

001 RE

-

[0 to 1023 / 0 / 1 digit/step]

002 RO

-

4694

[Black Level Read]

Displays the peak level of the black level scanning.

001 GE

-

[0 to 1023 / 0 / 1 digit/step]

002 GO

-

4695

[Black Level Read]

Displays the peak level of the black level scanning.

001 BE

-

[0 to 1023 / 0 / 1 digit/step]

002 BO

-

4802

[DF Shading FreeRun]

001 Lamp ON

-

Executes the scanner free run of shading movement
with exposure lamp on or off.
Press "OFF" to stop this free run. Otherwise, the free
run lasts.

002 Lamp OFF

4803

[Home Position Adjustment]

001 -

-

[-1 to 1 / 0 / 0.1 mm/step]

4804

[Home Position]

001 -

-

Executes the scanner HP detection.

System Service Mode

307

8

Содержание MPC 2800 AT-C2

























































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов