Ricoh MPC 2800 AT-C2 Скачать руководство пользователя страница 315 | Manualshive

Страница: 315 / 856

Ricoh MPC 2800 AT-C2 Скачать руководство пользователя страница 315

NVRAM\K5000017114.NV

7. In order to prevent an error during the download, be sure to mark the SD card that holds the uploaded

data with the number of the machine from which the data was uploaded.

• You can upload NVRAM data from more than one machine to the same SD card.

Downloading an SD Card to NVRAM

Do the following procedure to download SP data from an SD card to the NVRAM in the machine.

• The NVRAM data down load may fail if the SD card with the NVRAM data is damaged, or if the

connection between the controller and BICU is defective.

• Do the download procedure again if the download fails.
• Do the following procedure if the second attempt fails:
• Enter the NVRAM data manually using the SMC print you created before uploading the NVRAM

data.

1. Switch the copier main power switch off.
2. Remove the SD slot cover (



x 1).

3. Insert the SD card with the NVRAM data into SD Card Slot 3.
4. Switch the copier main power switch on.
5. Do SP5825-001 (NVRAM Data Download) and press the “Execute” key.

• The serial number of the file on the SD card must match the serial number of the machine for the

NVRAM data to download successfully. The download fails if the serial numbers do not match.

This procedure does not download the following data to the NVRAM:

• Total Count
• C/O, P/O Count

Address Book Upload/Download

Information List

The following information is possible to be uploaded and downloaded.

Information

Firmware Update

313

5

«
...
313
314
315
316
317
...
»

Содержание MPC 2800 AT-C2

























































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов