Ricoh MPC 2800 AT-C2 Скачать руководство пользователя страница 208 | Manualshive

Страница: 208 / 856

Ricoh MPC 2800 AT-C2 Скачать руководство пользователя страница 208

4. Third duct [A] (



x 2,



x 1)

5. Third duct fan [A] (3 hooks)

When reinstalling the third duct fan

Make sure that the third duct fan is installed with its decal facing to the upper side of the machine.

Toner Pump Unit

There are four pump units inside the machine. This procedure describes the replacement procedure only
for one unit. If you need to replace another unit, do the same as this procedure.

• Put some sheets of paper on the floor before doing this procedure. Toner may fall on the floor.

4. Replacement and Adjustment

206

4

«
...
206
207
208
209
210
...
»

Содержание MPC 2800 AT-C2

























































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов