Ricoh MPC 2800 AT-C2 Скачать руководство пользователя страница 339

Страница: 339 / 856

The following keys can be set with the corresponding numbers. (The initials in parentheses indicate
the names of the modules.)

4-Digit Entries for Keys 1 to 10

Key No.

Copy

Printer

Scanner

Web

2222 (SCS)

14000 (SRM)

256 (IMH)

1000 (ECS)

1025 (MCS)

4848 (COPY)

4400 (GPS)

5375 (Scan)

5682 (NFA)

2224 (BICU)

4500 (PDL)

5682 (NFA)

6600 (WebDB)

4600 (GPS-PM)

3000 (UCS)

3300 (PTS)

2000 (NCS)

6666 (WebSys)

2224 (BICU)

4126 (DCS)

2000 (NCS)

• The default settings for Keys 1 to 10 are all zero (“0”).

Key to Acronyms

Acronym

Meaning

Acronym

Meaning

ECS

Engine Control Service

NFA

Net File Application

GPS

GW Print Service

PDL

Printer Design Language

GSP-PM

GW Print Service – Print Module

PTS

Print Server

IMH

Image Memory Handler

SCS

System Control Service

MCS

Memory Control Service

SRM

System Resource Management

NCS

Network Control Service

WebDB

Web Document Box
(Document Server)

1. The machine is now set to record the debugging information automatically on the HDD (the target

selected with SP5857-002) for the events that you selected with SP5858 and the memory modules
selected with SP5859.

Using the Debug Log

337

Содержание MPC 2800 AT-C2

























































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MPC 2800 AT-C2

Отзывы:

Ricoh MPC 2800 AT-C2, Руководство по обслуживанию на месте, Страница: 339 / 856

Результаты поиска

Содержание MPC 2800 AT-C2

Отзывы: