Ricoh MPC 2800 AT-C2 Скачать руководство пользователя страница 332 | Manualshive

Страница: 332 / 856

Ricoh MPC 2800 AT-C2 Скачать руководство пользователя страница 332

NVRAM Data Upload/Download

Uploading Content of NVRAM to an SD card

Do the following procedure to upload SP code settings from NVRAM to an SD card.

• This data should always be uploaded to an SD card before the NVRAM is replaced.
• Make sure that the write protection of an SD card is unlocked

1. Do SP5990-001 (SMC Print) before you switch the machine off. You will need a record of the NVRAM

settings if the upload fails.

2. Switch the copier main power switch off.
3. Remove the SD slot cover (



x 1).

4. Insert the SD card into SD card slot 2. Then switch the copier on.
5. Execute SP5824-001 (NVRAM Data Upload) and then press the “Execute” key.
6. The following files are coped to an NVRAM folder on the SD card when the upload procedure is

finished. The file is saved to the path and the following filename:
NVRAM\<serial number>.NV
Here is an example with Serial Number “K5000017114”:
NVRAM\K5000017114.NV

7. In order to prevent an error during the download, be sure to mark the SD card that holds the uploaded

data with the number of the machine from which the data was uploaded.

• You can upload NVRAM data from more than one machine to the same SD card.

Downloading an SD Card to NVRAM

Do the following procedure to download SP data from an SD card to the NVRAM in the machine.

• The NVRAM data down load may fail if the SD card with the NVRAM data is damaged, or if the

connection between the controller and BICU is defective.

• Do the download procedure again if the download fails.
• Do the following procedure if the second attempt fails:
• Enter the NVRAM data manually using the SMC print you created before uploading the NVRAM

data.

1. Switch the copier main power switch off.

5. System Maintenance Reference

330

5

«
...
330
331
332
333
334
...
»

Содержание MPC 2800 AT-C2

























































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов