manualshive.com logo in svg

Ricoh MPC 2800 AT-C2, Руководство по обслуживанию на месте, Страница: 328 / 856

Поделиться
Скачать
Ricoh MPC 2800 AT-C2 Скачать руководство пользователя страница 328

SD Card Appli Move

Overview

The service program “SD Card Appli Move” (SP5-873) lets you to copy application programs from one
SD card to another SD card.
Slot 1 and Slot 2 are used to store application programs. However, more than two optional applications
are supplied for this machine. In that case, you can move application programs from Slot 2 to Slot 1 with
the following procedure.
Consider the following limitations when you try to merge SD cards.

• PostScript3 cannot be moved to the other SD card.
• The destination SD card should have the largest memory size of all the application SD cards. Refer

to the following table for the memory size of each SD card.

Outline of SD Card Appli Move:

1. Choose a SD card with enough space.

• Do not use an SD card if it has been used on a computer. Normal operation is not guaranteed

when such an SD card is used.

2. Enter SP5873 “SD Card Appli Move”. Then move the application from the SD Card in Slot 2 to the

card in slot 1.

3. Exit the SP mode

Use caution when you do the SD Card Appli Move procedure:

• The data necessary for authentication is transferred with the application program from an SD

card to another SD card. Authentication fails if you try to use the SD card after you copy the
application program from one card to another card.

5. System Maintenance Reference

326

5

Содержание MPC 2800 AT-C2

























































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов