Ricoh MPC 2800 AT-C2 Скачать руководство пользователя страница 504 | Manualshive

Страница: 504 / 856

Ricoh MPC 2800 AT-C2 Скачать руководство пользователя страница 504

021 Paper Tray1: Plain: 1200

*ENG

[–9 to 5 / 0 / 1 mm/step]

022 Tray1: Middle Thick: 1200

*ENG

023 Tray 2/3/4/5LCT: Plain: 1200

*ENG

024 Tray 2/3/4/5LCT: Mid: 1200

*ENG

025 By-pass: Plain: 1200

*ENG

026 By-pass: Middle Thick: 1200

*ENG

027 Paper Tray1: Thick1: 1200

*ENG

[–9 to 5 / -2 / 1 mm/step]

028

Paper Tray2/3/4/5/LCT: Thick
1:1200

*ENG

029 By-pass: Thick 1: 1200

*ENG

030 Duplex: Plain: 1200

*ENG

[–9 to 5 / 0 / 1 mm/step]

031 Duplex: Middle Thick: 1200

*ENG

032 Duplex: Thick 1: 1200

*ENG

[–9 to 5 / -2 / 1 mm/step]

1007

[By-Pass Size Detection] By-Pass Size Detection Display

001

LG

*ENG

[0 or 1 / 0 / 1 ]
0: Disable, 1: Enable

Enables or disables the automatic paper size detection function of the by-pass tray.
This SP determines what paper size the machine detects if the detected size is less than 8.5”.
0: OFF (Letter/SEF), 1: ON (Legal/SEF)

1101

[Flicker Control]

001

Flicker Control

*ENG

[0 or 1 / 0 / 1 /step]

-

1103

[Fusing Idling] Fusing Idling Adjustment

011 Idling Start Temp.

*ENG

[0 to 75 / 75 / 1 deg/step]

012 Forced Idling Stop

*ENG

[0 to 1 / 0 / 1 /step]

8. Appendix: SP Mode Tables

148

8

«
...
502
503
504
505
506
...
»

Содержание MPC 2800 AT-C2

























































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов