manualshive.com logo in svg

Ricoh MPC 2800 AT-C2, Руководство по обслуживанию на месте, Страница: 134 / 856

Поделиться
Скачать
Ricoh MPC 2800 AT-C2 Скачать руководство пользователя страница 134

• "ANT1" is a transmission/reception antenna and "ANT2" is a reception antenna. Do not attach

them at the wrong places.

7. Attach the clamps as shown above.
8. Wire the cables and clamp them (

 x 7).

• Make sure that the cables are not slack. Keep them wired tightly along the covers.

You may have to move the machine if the reception is not clear.

• Make sure that the machine is not located near an appliance or any type of equipment that generates

strong magnetic fields.

• Put the machine as close as possible to the access point.

Installing Hardware Combinations

• Refer to the above picture when installing the handset and the USB2.0/SD.

UP Mode Settings for Wireless LAN

Enter the UP mode. Then do the procedure below to perform the initial interface settings for IEEE 802.11
a/g, g. These settings take effect every time the machine is powered on.

• You cannot use the wireless LAN if you use Ethernet.

1. Press the “User Tools/Counter” key.
2. On the touch panel, press “System Settings”.

• The Network I/F (default: Ethernet) must be set for either Ethernet or wireless LAN.

2. Installation

132

2

Содержание MPC 2800 AT-C2

























































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов