Renesas RX100 Series Скачать руководство пользователя страница 396 | Manualshive

Страница: 396 / 1041

background image

R01UH0822EJ0100 Rev.1.00

Page 396 of 1041

Jul 31, 2019

RX13T Group

19. Multi-Function Timer Pulse Unit 3 (MTU3c)

(1) Example of Buffer Operation Setting Procedure

shows an example of the buffer operation setting procedure.

Figure 19.16

Example of Buffer Operation Setting Procedure

(2) Examples of Buffer Operation

(a) When TGR is an Output Compare Register

shows an operation example in which PWM mode 1 has been designated for MTU0, and buffer operation

has been designated for TGRA and TGRC. The settings used in this example are TCNT clearing by compare match B,
high output at compare match A, and low output at compare match B. In this example, the TTSA bit in TBTM is set to 0.
As buffer operation has been set, when compare match A occurs, the output changes and the value in buffer register
TGRC is simultaneously transferred to timer general register TGRA. This operation is repeated each time compare
match A occurs.
For details of PWM modes, refer to

section 19.3.5, PWM Modes

Figure 19.17

Example of Buffer Operation (1)

[1]

[2]

[3]

Buffer operation

Select TGR function

Set buffer operation

Start count

<Buffer operation>

[1] Designate TGR as an input capture register or

output compare register by means of TIOR.

[2] Designate TGR for buffer operation with bits BFA

and BFB in TMDR1.

[3] Set the CSTn bit in TSTRA to 1 to start the count

operation.

TCNT value

Time

0200h

0520h

0200h

0450h

0520h

0450h

0450h

0200h

Transfer

MTU0.TGRB

0000h

MTU0.TGRC

MTU0.TGRA

MTIOC0A

MTU0.TGRA

«
...
394
395
396
397
398
...
»

Содержание RX100 Series


















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RX100 Series

Бренд: Idis Страницы: 123

Бренд: Idis Страницы: 29

Бренд: Idis Страницы: 28

DirectIP DR-1304P

Бренд: Idis Страницы: 82

Бренд: NA Страницы: 22

FieldPoint cFP-RTD-122

Бренд: National Instruments Страницы: 15

Storage Networking (Unified Fabric Pilot)

Бренд: Qlogic Страницы: 76

Low Power Series

Бренд: FabiaTech Страницы: 77

4 Channel Input Buffer Board SDAIBB

Бренд: B&B Electronics Страницы: 22

Бренд: SriHome Страницы: 12

Бренд: Keysight Technologies Страницы: 106

X-NUCLEO-EEPRMA1

Бренд: ST Страницы: 22

Бренд: ALIBI Страницы: 232

Wireless Outdoor Bridge XI-1500-IH

Бренд: IMC Networks Страницы: 13

BPN-SAS3-116A-N10

Бренд: Supermicro Страницы: 8

Бренд: IBM Страницы: 242

Бренд: XMOS Страницы: 8

Бренд: Rosewill Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды