Radyne ComStream TIERNAN SE4000 Скачать руководство пользователя страница 98 | Manualshive

Страница: 98 / 161

background image

SE4000 MPEG-2 Contribution Encoder

Configuring the SE4000

01-0934-401-B

5-1

Configuring the SE4000

5

This chapter presents the following information:

•

Configuration prerequisites.

•

A high-level procedure used to configure a SE4000 using either the front panel or a
remote unit.

•

Detailed procedures for configuring a SE4000 to the default standards, using either
the front panel or a remote unit

•

Examples of common SE4000 configurations, including:

•

Configuraing a basic DSNG setup using the front panel.

5.0 SE4000 Configuration Procedure

Whether the front panel or a remote unit is used to configure the SE4000, perform the following
steps to configure the system:

1.

Make a list of the operational requirements.

2.

Compare the requirements to the corresponding SE4000 default parameter settings

3.

Determine which SE4000 default parameters must be changed for the operational
requirements.

4.

Record the new SE4000 parameter values and the corresponding front panel or remote
commands required to change those parameters.

5.

Configure the SE4000 to the default configuration.

6.

Configure the SE4000 with any new parameters.

7.

Ensure that any decoders are correctly configured to operate with the SE4000 parameter
settings.

All SE4000 configuration changes issued from the front panel are
automatically save to non-volatile memory. Unlike front panel operations,
SE4000 parameter changes made from a remote unit are not
automatically saved to non-volatile memory. If configuration changes are
made from a remote unit, issue the command

CM SAVE

to save the

configuration to non-volatile memory. Multiple configurations can be
saved using the Quickset commands.

«
...
96
97
98
99
100
...
»

Содержание TIERNAN SE4000


































































































































































Отзывы:

Нет отзывов

Похожие инструкции для TIERNAN SE4000

MediaLounge DSM-520

Бренд: D-Link Страницы: 2

Бренд: Planet Страницы: 7

Бренд: matson Страницы: 11

Бренд: FireBird Страницы: 44

VECTOPOWER VP600 Series

Бренд: Aradex Страницы: 114

Бренд: Nightlife Страницы: 12

Бренд: Viking Страницы: 6

Бренд: Baumer Страницы: 41

Бренд: FBS Страницы: 6

Бренд: KONANlabs Страницы: 6

Бренд: Kramer Страницы: 25

Бренд: Pentax Страницы: 44

Бренд: Sioux Tools Страницы: 5

Бренд: DROPSA Страницы: 8

Бренд: Wacker Neuson Страницы: 36

Q.HOME CORE H Series

Бренд: Qcells Страницы: 28

Бренд: Hoymiles Страницы: 2

Бренд: TECO Страницы: 93

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды