Radyne ComStream TIERNAN SE4000 Скачать руководство пользователя страница 47

Страница: 47 / 161

Using a Remote Unit

SE4000 MPEG-2 Contribution Encoder

4-14

01-0934-401-B

Front Panel Menu Summary

Command

Function

Options/Response Format

Config>Service

#>Video>Enco

der

Used to configure the SE4000 video encoding parameters.

Enable

Setting determines whether or

not video is included in the

output transport stream.

? on – video is included in the output transport

stream (default).

? off – video is not include in the output transport

stream.

PID

Query only. Displays the video

PID number included in the

output transport stream.

Default – 33 (21h)

Bit Rate

Sets the output compressed

video bit rate for optimum video

performance.

? If the Tx Strm>Rate Calc is

set to auto, this command is

query only.

? If the Tx Strm>Rate Calc is

set to manual, the user sets

the data rate.

If chroma set to 4:2:0: 1.0 to 15.0 Mbps
if chroma set to 4:2:2: 2.5 to 50.0 Mbps

Aspect Ratio

Sets the picture aspect ratio

which is the ratio of the frame

width to the frame height.

? 4x3 (default)
? 16x9

Selects the picture resizing that

the SE4000 performs prior to

video encoding.

720, 704, 544, 480, 352
default: 720

Horizontal

Resolution

Additional Information: As shown in the following table, the number of lines depends

upon whether the video format is set to NTSC or PAL.

Resolution

Encoding

OptionNTSC Mode

PAL-I Mode

Type

AFF352

352 pixels by 480 lines

352 pixels by 576 lines

MPEG – 2

AFF480

480 pixels by 480 lines

480 pixels by 576 lines

MPEG – 2

AFF544

544 pixels by 480 lines

544 pixels by 576 lines

MPEG – 2

AFF704

704 pixels by 480 lines

704 pixels by 576 lines

MPEG – 2

AFF720

720 pixels by 480 lines

720 pixels by 576 lines

MPEG – 2

(default)

(full resolution video)

Chroma

Sets the chrominance

compression algorithm.

4:2:0, 4:2:2 optional

Содержание TIERNAN SE4000


































































































































































Результаты поиска

Содержание TIERNAN SE4000

Отзывы:

Похожие инструкции для TIERNAN SE4000

Бренды по названию

Популярные бренды

Radyne ComStream TIERNAN SE4000, Инструкция по установке и эксплуатации

Результаты поиска

Содержание TIERNAN SE4000

Отзывы:

Похожие инструкции для TIERNAN SE4000

Бренды по названию

Популярные бренды