Radyne ComStream TIERNAN SE4000 Скачать руководство пользователя страница 127 | Manualshive

Страница: 127 / 161

background image

VBI Data Transmission

SE4000 MPEG-2 Contribution Encoder

B-6

01-0934-401-B

1.

Ensure that all other VBI schemes are disabled, including Teletext, ATSC closed
captions, and Tiernan closed captions.

2.

Ensure that VBI data is included in the selected service vi deo input signal.

3.

Set chroma to 4:2:2 mode. Issue the front panel command
Config>Service>Video>Chroma=4:2:2 or the remote VE CHROMA 4_2_2 command.

4.

Configures the encoder to transmit either 16 or 32 lines of VBI information. Issue the
front panel command Config>Service>VBI>Expand> VBI_Passthru=type or the
remote VE VBI_PASS type command, where type is set to 16_lines or 32_lines.

Decoder

5.

Ensure that Teletext mode is set to off. Issue the front panel command
VBI>Teletext>Mode=Off or the remote VBI TELETEXT MODE OFF command.

6.

Set the decoder VBI format control to automatically detect the type of VBI data to decode.
Issue the front panel command VBI>Format>VBI Format Cntrl=Auto or the remote
VBI CONTROL AUTO command.

7.

If your system requires you to manually set the type of VBI data to Expanded Windows,
follow these steps:

a.

Set the decoder VBI format control to manual. Issue the front panel command
VBI>Format>VBI Format Cntrl=Manual or the remote VBI CONTROL MANUAL
command.

b.

Set the VBI format to either 16- or 32-lines Expanded Windows.

From the front panel, issue the command VBI>Format>VBI Format=# where # is set to 16-line or
32-line.

From a remote terminal, issue the command VBI FORMAT # where # is set to lines16 or lines32.

«
...
125
126
127
128
129
...
»

Содержание TIERNAN SE4000


































































































































































Отзывы:

Нет отзывов

Похожие инструкции для TIERNAN SE4000

Бренд: ultimatte Страницы: 125

Бренд: 3One data Страницы: 9

Бренд: Parker Страницы: 36

CSI-75K-T40001-E

Бренд: CanadianSolar Страницы: 45

DuoPak APD 2067

Бренд: Absolute Process Instruments Страницы: 2

OTEC IEWQ Series

Бренд: Omega Страницы: 29

Бренд: E-Lektron Страницы: 7

Бренд: Coretec Страницы: 38

Бренд: NAIM Страницы: 28

Бренд: Wacker Neuson Страницы: 36

Бренд: Lindy Страницы: 14

Бренд: Walter Страницы: 216

Бренд: Gorman-Redlich Страницы: 3

MAXX SST VEC049GM

Бренд: Vector Страницы: 10

Бренд: KDS Страницы: 4

Бренд: Intech Страницы: 4

basic-line DCC 1-00

Бренд: axing Страницы: 4

Бренд: Linear Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды