Radyne ComStream TIERNAN SE4000 Скачать руководство пользователя страница 131

Страница: 131 / 161

Conditional Access

SE4000 MPEG-2 Contribution Encoder

C-2

01-0934-401-B

Select a Service

From the main menu, select Config>CA>Setup>Service. A list of all available services
displays.

If only one service is available, the service parameter is query-only, as this one service is
automatically selected.

Scroll through the list to select the service to be configured for BISS scrambling and
press Enter. The Scramble menu displays.

Ensure that the correct service name displays in the menu line. If the displayed service is
incorrect, return to Step 1.

Enable BISS for that Service

From the Scramble menu, select BISS Mode 1 and press Enter.

When the asterisk disappears, press the right arrow key to go to the BISS key parameter.

Enter the Scramble Key

Use the numeric keypad to enter the 12-digit key. Once all 12 digits are entered, the key
will begin to flash. Press Enter.

When the asterisk disappears, the BISS configuration settings are immediately
implemented for that service.

Continue to Enable and Disable Individual Services, as Required

Continue selecting services and enabling/disabling each as required.

SE4000 is Now Processing Data Using the Current BISS Configuration

BISS is now enabled and will continue to use the current BISS configuration until BISS is
disabled (turned off) or the BISS configuration is changed.

Disable BISS for an Individual Service

To disable BISS for a selected service, perform these steps:

1.

From the main menu, select Config>CA>Setup>Service. A list of all available services
displays.

Scroll through the list to select the service to be configured for BISS scrambling and
press Enter. The Scramble menu displays. Ensure that the correct service name
displays in the menu line.

If the displayed service is incorrect, return to step 1.

From the Scramble menu, select None and press Enter.

Conditional access is now disabled for the selected service.

Even though BISS conditional access may be disabled for a service, the SE4000 retains the BISS
scramble key set for that service.

Содержание TIERNAN SE4000


































































































































































Результаты поиска

Содержание TIERNAN SE4000

Отзывы:

Похожие инструкции для TIERNAN SE4000

Бренды по названию

Популярные бренды

Radyne ComStream TIERNAN SE4000, Инструкция по установке и эксплуатации

Результаты поиска

Содержание TIERNAN SE4000

Отзывы:

Похожие инструкции для TIERNAN SE4000

Бренды по названию

Популярные бренды