Radyne ComStream TIERNAN SE4000 Скачать руководство пользователя страница 109

Страница: 109 / 161

Troubleshooting

SE4000 MPEG-2 Contribution Encoder

6-6

01-0934-401-B

Once a fault condition sets the fault relay and illuminate the status LED on the front panel, they
must be cleared manually by either:

•

Selecting the front panel Status>Relay>Clear option.

•

Issuing a remote

FM RELAY_CLR

command.

6.4.1 Viewing Fault Relay Log on the Front Panel

The Relay fault History works similarly to the History and Current menus. To view the fault history
log on the front panel, perform these steps.

1.

From the main menu, select the Status menu.

SE4000 >

QUICKSET SERVICE OUTPUT [STATUS]

The Status menu displays. Select Relay.

SE4000/Status    >

Current History [ Relay ]

The Fault Relay menu displays. You may scroll through the fault list displayed in a

similar manner to the fault history described above.

SE4000/Status/Relay    >

Digital Video Loss of Input

The LCD displays the most recent faults. In order to clear rthe fault relay, you must press
the right arrow. The display will be as below.

SE4000/Status/Relay     >

Press enter to Clear Fault Relay List

Pressing enter will reset the fault relay and clear all of the faults saved in the list. If no
faults exist, the LCD displays

No Fault.

Содержание TIERNAN SE4000


































































































































































Результаты поиска

Содержание TIERNAN SE4000

Отзывы:

Похожие инструкции для TIERNAN SE4000

Бренды по названию

Популярные бренды

Radyne ComStream TIERNAN SE4000, Инструкция по установке и эксплуатации

Результаты поиска

Содержание TIERNAN SE4000

Отзывы:

Похожие инструкции для TIERNAN SE4000

Бренды по названию

Популярные бренды