Radyne ComStream TIERNAN SE4000 Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 161

background image

Introduction

SE4000 MPEG-2 Contribution Encoder

2-2

01-0934-401-B

2.1 Powering On The SE4000

The rear panel AC power supply interface includes a fuse holder, and an IEC 320 power cord
receptacle. The typical SE4000 configuration requires 70 Watts.

An auto-sensing, auto-ranging AC switching power supply powers the SE4000 unit. The supply
accepts 100 to 240 VAC nominal input voltage levels cycling at 50 to 60 Hz. A 6 Amp fuse on the
rear panel protects the power supply from excessive current.

The On/Off (1/0) power switch is located on the front panel.

2.1.1 AC Power Cords

The SE4000 shipping kit includes two AC power cords, one for North American applications,
specifically the United States and Canada, and the other for international applications.

AC wiring must be done in accordance with governmental standards and
codes in effect at the SE4000 installation site. Refer to the Safety
Precautions for additional information.

2.1.2 North American Applications

One cord has an IEC- compatible female plug on one end and a North American male plug on the
other. This cord is UL and CSA approved up to 125 VAC at 10 A. This cord is ready to use with
no user wiring required.

2.1.3 International Applications

The international cord has an IEC-compatible female plug on one end and three stripped and
tinned bare wires on the other end. This cord is approved by many international safety agencies,
including VDE, up to 250 VAC at 6 A.

2.1.4 Connecting to a Power Source

To connect to an AC power source, follow these steps:

1.

Select an AC power cord. If an international power cord is selected, attach a
connector in accordance with local regulations and laws.

2.

Ensure the SE4000 power switch is in the Off, or 0 position.

3.

Connect the female plug of the AC power cord to the AC power receptacle on the
SE4000 rear panel.

4.

Connect the male plug of the AC power cord to an external AC power
conditioning surge suppressor.

5.

Connect the AC power conditioning surge suppressor to an AC outlet.

«
...
21
22
23
24
25
...
»

Содержание TIERNAN SE4000


































































































































































Отзывы:

Нет отзывов

Похожие инструкции для TIERNAN SE4000

MediaLounge DSM-520

Бренд: D-Link Страницы: 127

DivX Connected DSM-330

Бренд: D-Link Страницы: 38

Бренд: Eco Drive Страницы: 138

Бренд: ICP DAS USA Страницы: 4

AT-IMC100T/SCMM

Бренд: Allied Telesis Страницы: 20

Бренд: Versus Audio Страницы: 12

Бренд: B&B Electronics Страницы: 2

Бренд: KanexPro Страницы: 32

Бренд: FOLSOM Страницы: 61

THE-S55P3BB-USW

Бренд: Tabuchi Electric Страницы: 64

Бренд: Votek Страницы: 33

Бренд: Littfinski Daten Technik Страницы: 2

EQUINOX EQX2 4002-HT

Бренд: Salicru Страницы: 108

Бренд: opticis Страницы: 19

MCT-2612 SERIES

Бренд: CTS Страницы: 2

Бренд: M-system Страницы: 4

Бренд: Audio Nemesis Страницы: 10

Бренд: MPP Solar Страницы: 59

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды