Radyne ComStream TIERNAN SE4000 Скачать руководство пользователя страница 118

Страница: 118 / 161

SE4000 MPEG-2 Contribution Encoder

Technical Specifications

01-0934-401-B

A-1

Technical Specifications

STANDARD FEATURES

Video Input

Analog

Serial Digital

•

PAL (625 line) or NTSC (525 line) formats.

•

SMPTE 170M NTSC or ITU-R BT.470-6 PAL-
I/B/D, BNC connector.

•

SMPTE 259M SDI @ 270 Mbps, BNC
connector.

Video Processing

•

MPEG-2 4:2:0 (Main Profile @ Main Level), 1.0
to 15.0 Mbps.

•

Horizontal resolutions: 720, 704, 640, 544, 480
and 352 pixels/line.

•

Vertical resolutions 240 or 480 lines (NTSC) or
288 or 576 lines (PAL).

•

4:3 and 16:9 configurable aspect ratio.

•

TBC, AGC, and clamp for composite video
signal restoration.

Vertical Blanking Interval

•

Proprietary passing of NTSC line 21 closed-
captions (composite or SDI).

•

ATSC closed-captions, per A/53 (composite or
SDI).

•

DVB Teletext for World System Teletext on
PAL composite video.

Latency

•

Ultra-low latency: 150 ms (encode to decode).

•

Low latency: 200 ms (encode to decode).

•

Quality: 350 to 1000 ms (encode to decode).

Audio Inputs

•

Two stereo or four independent analog mono
channels on balanced XLR connectors.

•

Two AES/EBU digital stereo pairs on 75 Ohm
BNC connectors.

Audio Processing

•

MPEG-1 Layer II

•

Two stereo channels or four independent mono
channels

•

Sampling rates of 32, 44.1 and 48 Ksps

•

Output rates from 64 to 384 Kbps.

Auxiliary Data

•

One synchronous: 1 to 20 Mbps, resolution 1
bps, EIA-422, on female DB-9 connector.

•

One asynchronous: 1200 to 115 Kbps, EIA-
232, on female DB-9 connector.

Control Tables

•

Internally generated DVB-compatible PSI/SI
tables.

Conditional Access

•

PGCA proprietary conditional access,
enable/disable IRDs from front panel or remote
control.

Содержание TIERNAN SE4000


































































































































































Результаты поиска

Содержание TIERNAN SE4000

Отзывы:

Похожие инструкции для TIERNAN SE4000

Бренды по названию

Популярные бренды

Radyne ComStream TIERNAN SE4000, Инструкция по установке и эксплуатации

Результаты поиска

Содержание TIERNAN SE4000

Отзывы:

Похожие инструкции для TIERNAN SE4000

Бренды по названию

Популярные бренды