Safety & Compliance Notices:
Notice Concerning FCC Regulations:
You are cautioned that
changes or modifications not expressly approved by the part responsible for compliance could void the
user’s authority to operate the equipment. This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation. This equipment
generates uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the following measures: (
a
)
Reorient or relocate the receiving antenna; (
b
) move this unit; (
c
) increase the separation between the
equipment and receiver; (
d
) connect the equipment into an outlet on a circuit different from that to which
the receiver is connected; (
e
) be sure that all cables are properly shielded, using a choke or ferrite where
appropriate; (
f
) consult the dealer or an experienced radio/television technician for help.
User Guide
(English)
For more information
about this product (system requirements, compatibility
information, etc.), product registration, or product support, visit
m-audio.com
.
For safety and warranty information, visit
m-audio.com
/
warranty
.
Package Contents:
Transit Pro, USB cable, 1/8”-to-stereo-RCA cable,
1/8”-to-TOSLINK
®
digital cable, User Guide
Windows users:
Visit
m-audio.com
/
drivers
to download the necessary
Windows drivers for Transit Pro.
1.
Power Input:
Use a power adapter (5 VDC, 500 mA, center-
positive, sold separately) to connect this input to a power outlet.
2.
USB Port:
Insert this connector to a USB port on your
computer (powered on).
3.
Main Output:
Use an 1/8” (3.5mm) stereo cable to connect this
output to the analog input of an active speaker. Alternatively,
connect it to the digital input of a receiver.
4.
Headphone Output:
Connect standard 1/4” (6.35mm) or 1/8”
(3.5mm) stereo headphones to either of these outputs.
5.
Volume:
Turn this knob to set the volume of the
main output
and
headphone output
.
6.
Power Indicator:
This light illuminates when Transit Pro is
powered on.
7.
Analog Output Indicator:
This light illuminates when Transit
Pro is successfully sending an analog signal out of its left/right
analog outputs.
8.
DSD Indicators:
One of these lights illuminates to indicate its
current Direct Stream Digital rate:
DSD64
or
DSD128
.
9.
Sampling Rate Indicators:
One of these lights illuminates to
indicate which sampling rate Transit Pro is currently using: 44.1,
48, 88.2, 96, 176.4, 192, 352.8, or 384 kHz.
Guía del usuario
(Español)
Para más información
acerca de este producto (requisitos de sistema,
información de compatibilidad, etc.), registro o soporte del producto,
visite
m-audio.com
. Para información sobre la seguridad y la garantía,
visite
m-audio.com
/
warranty
.
Contenido del paquete:
Transit Pro, cable USB, cable de 3,5 mm (1/8 pulg.) a
RCA estéreo, cable digital de 3,5 mm (1/8 pulg.) a TOSLINK
®
, guía del usuario
Usuarios de Windows:
Visitar
m-audio.com
/
drivers
para descargar los
drivers de Windows necesarios para Transit Pro.
1.
Entrada de corriente:
Utilice un adaptador de corriente (5 V CC,
500 mA, centro positivo, que se vende por separado) para conectar
esta entrada a una toma de corriente.
2.
Puerto USB:
Inserte este conector en un puerto USB de su
ordenador (encendido).
3.
Salida principal:
Utilice un cable estéreo de 3,5 mm (1/8 pulg.) para
conectar esta salida a la entrada analógica de un altavoz activo.
Como alternativa, conéctela a la entrada digital de un receptor.
4.
Salida para auriculares:
Conecte auriculares estéreo estándar de 6,35
mm (1/4 pulg.) o de 3,5 mm (1/8 pulg.) a cualquiera de estas salidas.
5.
Volumen:
Gire esta perilla para ajustar el volumen de la
salida
principal
y la
salida para auriculares
6.
Indicador de encendido:
Esta luz se ilumina cuando el Transit Pro
está encendido.
7.
Indicador de salida analógica:
Esta luz se enciende cuando el
Transit Pro envía exitosamente una señal de salida analógica a sus
salidas analógicas izquierda/derecha.
8.
Indicadores DSD:
Una de estas luces se ilumina para indicar su
tasa actual de Direct Stream Digital:
DSD64
o
DSD128
.
9.
Indicadores de frecuencia de muestreo:
Una de estas luces se
enciende para indicar qué frecuencia de muestreo está utilizando el
Transit Pro en ese momento: 44,1, 48, 88,2, 96, 176,4, 192, 352,8 o
384 kHz.
Technical Specifications
Connections:
(1) 1/8” (3.5mm) analog/digital
(1) 1/8” (3.5mm) stereo headphone
(1) 1/4” (6.35mm) stereo headphone
(1) USB port
Sampling Rates:
44.1, 48, 88.2, 96, 176.4, 192, 352.8, 384 kHz
Direct Stream Digital Rates:
DSD64, DSD128
Power:
USB or
power adapter (5 VDC, 500 mA, center-positive, sold separately)
Dimensions
(WxDxH)
:
2.6” x 3.7” x 1.2” / 67 x 94 x 30 mm
Weight:
0.39 lbs. / 0.18 kg
Specifications are subject to change without notice. Manual Version 1.1
This device complies with Part 15 of the FCC rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
FCC RF Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits
set forth for an uncontrolled environment. End users must follow the specific operating instructions for
satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction
with any other antenna or transmitter. For best audio quality, avoid using this device in a high RF-
radiated environment.
RSS Statement for Canadian models:
This device complies with Industry
Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (
1
) this
device may not cause interference, and (
2
) this device must accept any interference, including
interference that may cause undesired operation of the device This unit does not exceed the Class B
limits for radio noise emission from digital apparatus set out in the radio interference regulations of the
Canadian Department of Communications.
ESD
/
EFT Warning:
This unit may contain a microcomputer for signal processing and
control functions. In very rare situations, severe interference, noise from an external source,
or static electricity may cause it to lock up. In the unlikely event that this should happen,
turn off the unit, wait at least five seconds, and then turn it back on again.
In an
environment with radio frequency interference, the unit may malfunction and resume
normal operation after removal of the interference.
Trademarks and Licenses:
M-Audio is a trademark of inMusic Brands, Inc., registered in the U.S.
and other countries.
Direct Stream Digital (DSD) and Sony are trademarks or registered trademarks of
Sony Corporation or any of its affiliates. TOSLINK
®
is a registered trademark of Toshiba Corporation. All
other product or company names are trademarks or registered trademarks of their respective owners.
User Guide
Guía del usuario
Guide d’utilisation
Guida per l’uso
Benutzerhandbuch
English
Español
Français
Italiano
Deutsch
1
2
3
4 4
5
5
6
7
8
9
9
8
1
2
3
4 4
5
5
6
7
8
9
9
8
