Radiodetection 6100-Gfast Скачать руководство пользователя страница 158

Страница: 158 / 213

6100-Gfast Multifunction Network Analyzer Operation Manual

158

VDSL2/ADSL2+

- if VDSL2 option

enabled

ADSLMulti

supports G.DMT, T1.413,

and G.Lite.

ADSL2+ Bonding

- if VDSL2 option

disabled, Bonding option enabled.

VDSL2/ADSL2+ Bonding

- if VDSL2

and Bonding options enabled.

VDSL2-30a

- if VDSL2 option enabled.

The

6100-Gfast

unit does ADSL Annex A and

Annex B. ADSL Annex A is on pair 2 and ADSL
Annex B is on pair 1.



The

Test Interface

setup options are as

follows:

VDSL2/ADSL2+ (xB/P1)

- if VDSL2

option enabled, ADSL Annex B mode.

ADSLMulti (xB/P1)

- supports G.DMT

only.

VDSL2/ADSL2+ (xA/P2)

- if VDSL2

option enabled, ADSL Annex A mode.

ADSLMulti (xA/P2)

- support G.DMT

and T1.413 only.

ADSL2+ (xB/P1)

- if VDSL2 option

disabled, ADSL Annex B mode.

ADSL2+ (xA/P2)

- if VDSL2 option

disabled, ADSL Annex A mode.

VDSL2-30a (Pair 1)

- if VDSL2 option

is enabled.

VDSL2 Bonding

- if VDSL2 and

Bonding options are enabled.

The

6100-Gfast-Bond

unit does ADSL Annex A

on pair 1 and supports bonding.



The

Test Interface

setup options are as

follows:

G.fast

if enabled.

VDSL2/ADSL2+

- if VDSL2 option

enabled.

ADSLMulti

supports G.DMT, T1.413,

and G.Lite.

VDSL2/ADSL2+ Bonding

- if VDSL2

and Bonding options enabled.

VDSL2-35b

if enabled.

The

6100-Gfast

unit does ADSL

Annex B

and

UR2

which can be configured in

Setup

Modem

Settings

DSLAM

. ADSL Annex A is on pair 1, and

ADSL Annex B and UR2 are on pair 2. This modem
does not support bonding.



Test Interface

options are as follows:

G.fast (Pair 1)

VDSL2/ADSL2+ (xA/Pair 1)

ADSLMulti (xA/Pair 1)

VDSL2-35b (Pair 1)

ADSL2+ (xB/Pair 2)

ADSLMulti (xB/Pair2)

ADSL2+ (UR2/Pair 2)

ADSLMulti (UR2/Pair 2)



Annex M

allows you to Enable/Disable this

option when Test Interface is:

VDSL2/ADSL2+ or VDSL2/ADSL2+

Bonding for 6100-Gfast-Bond units.

VDSL2/ADSL2+ (xA/Pair 1) for 6100-

Gfast unit.



Annex J

allows you to Enable/Disable this

option when Test Interface is:

ADSL2+ (xB/Pair 2) for 6100-Gfast

unit.



ADSL Transport

displays the transport type

options:

PTM

(packet transfer mode),

ATM

(asynchronous transfer mode), or

ATM and

PTM

. When

G.fast

is selected as the

Test

Interface

ADSL Transport

is disabled.



Access Mode

options are dependent on the

test setup selection.

For Auto and Manual tests, available

options are:

Sync Only, Bridged

(not

in Auto Test),

DHCP, Static, PPPoE,

PPPoA, IPoA

, and

IPv6 (DHCP).

For Ethernet tests, available options

are Bridged, DHCP, Static,

PPPoE

and

IPv6 (DHCP)

Note: IPv6 requires an option to be enabled, please

contact Radiodetection for details.



Auto Resync

allows you to

Enable

the

SyncLossCounter as the Pass/Fail criteria.
When SyncLoss1 is reached, the test
will have fail status.



Auto Resync

is disabled, any time the test

loses sync, the result status will be fail and the
test will stop automatically.



Sync Timeout Period

enables you to enter the

duration, between 2 and 30 minutes, to run a
DSL test from activation to reaching

Show

Time

Содержание 6100-Gfast






















































































































































































































Результаты поиска

Содержание 6100-Gfast

Отзывы:

Похожие инструкции для 6100-Gfast

Бренды по названию

Популярные бренды

Radiodetection 6100-Gfast, Руководство по эксплуатации

Результаты поиска

Содержание 6100-Gfast

Отзывы:

Похожие инструкции для 6100-Gfast

Бренды по названию

Популярные бренды