Radiodetection 6100-Gfast Скачать руководство пользователя страница 120

Страница: 120 / 213

6100-Gfast Multifunction Network Analyzer Operation Manual

120

Single Tone

The

Single Tone

tab allows you to configure the

following parameters:



Current Group

is the current test group name,

for example

Frequency Tests



Current Test

displays the test being

measured. Here you can switch to another
Frequency test from the given list. However,
this action will terminate the ongoing
measurement test.



Receive Tone

allows you to select either a

(voice frequency) or

(wideband) signal.

selection is only available when the

MHz Wideband Testing

software option is

installed.



Termination Resistance

defines how much

resistance the tester uses to connect to the
line, and is set as follows:

for

VF Tone

, a read-only value of

600

Ω.

for

WB Tone

, select 100, 120, or

135

Ω.



FED Frequency

sets the frequency that the

TS125 FED will transmit and is a value in Hz
for

VF Receive Tone

(default 300 Hz) and kHz

for

(default 196 kHz).



Tone Duration

modifies the duration value of

the tone from 5 - 60 seconds. Default is

5 s



Result

displays the values for both the RX

VF/WB Loss and Frequency



Test Status

displays the current state of

measurement or an error message.

To select the parameter values:

1. Press the up/down arrow keys to highlight the

desired parameter.

2. Press the left/right arrow keys to view and

select the options.

3. Press

on a value to open a list box of

options or the alphanumeric editor screen and
use the navigation keys to scroll through.

4. Press

to confirm the value.

Single Tone Result Details

The

Result Details

read-only page displays the saved

receive tone or

VF/WB RX Loss/Frequency

values for

the

Single RX Tone with FED

test.

Содержание 6100-Gfast






















































































































































































































Результаты поиска

Содержание 6100-Gfast

Отзывы:

Похожие инструкции для 6100-Gfast

Бренды по названию

Популярные бренды

Radiodetection 6100-Gfast, Руководство по эксплуатации

Результаты поиска

Содержание 6100-Gfast

Отзывы:

Похожие инструкции для 6100-Gfast

Бренды по названию

Популярные бренды