Radiodetection 6100-Gfast Скачать руководство пользователя страница 16

Страница: 16 / 213

6100-Gfast Multifunction Network Analyzer Operation Manual



LCD backlight turns off after system idles (no
keys pressed) for 10 min.



Unit switches to suspend mode after timeout:
10 min.



Power Save Mode

Disable

requiring you to

go to this page to see what will be changed
before enabling it.

The chart displays the following battery measurements:
capacity, current, and voltage.

Battery Status

indicates

the current power level, as a percentage, for the
battery.

To change the power scheme settings:

1. Press , select

System Settings

, and then

Battery Info

2. Under

DC IN

BATTERY

, use the arrow keys

to select

Idle

suspend timeout

modes. Press

to view the list of available choices or use

the left/right arrow keys.

3. Select a new value, then press

to confirm

the choice. Repeat for the other modes as
needed.

6.7 Software Options

To activate a newly purchased option key on your
6100-Gfast, please contact Radiodetection. The unit
may require returning to Radiodetection.

DSL Options

This screen lists all the DSL Configured Options that
are present on the unit.

Possible options are as follows:



VDSL2MOD

(

Support VDSL2 test

)



PING

(

Support Ping and IP login

)



FTP

(

FTP Test Support

)



Traceroute

(

Traceroute Test Support

)



Browser

(

Web Browser Support

)



IPTV

(

IPTV Test Support

)



BOND

(

Bonding

) (only supported by

6100-Gfast-Bond)



VOIP

(

VoIP Test Support

)



MOS

(

MOS / R-Factor Scores

)



IPV6

(

IPv6 Support

)



GFAST

(

G.fast Support

)



VDSL2-35B

(

VDSL2-35B Support

)



Bandwidth Speed Test over DSL/Ethernet

Copper Options

This screen lists all the

Copper Configured Options

that are present on the unit. Possible options are as
follows:



TDR



RFL



FaultMapper



Pair Detective



Wideband Testing



Near End Crosstalk



High Voltage Isolation Resistance

Содержание 6100-Gfast






















































































































































































































Результаты поиска

Содержание 6100-Gfast

Отзывы:

Похожие инструкции для 6100-Gfast

Бренды по названию

Популярные бренды

Radiodetection 6100-Gfast, Руководство по эксплуатации

Результаты поиска

Содержание 6100-Gfast

Отзывы:

Похожие инструкции для 6100-Gfast

Бренды по названию

Популярные бренды