manualshive.com logo in svg

PI MS249E, Руководство пользователя, Страница: 9 / 279

Поделиться
Скачать
PI MS249E Скачать руководство пользователя страница 9

 

 

1 About this Document 

C-863.12 Mercury Controller 

MS249E 

Version: 1.2.1 

3 

Term 

Explanation 

feedback. After the controller is switched on, referencing must be done 
before absolute target positions can be commanded and reached. 

PC software 

Software installed on the PC. 

Nonvolatile memory 

Memory module (read-only memory, e.g., EEPROM or flash memory) 
where the default values of the parameters are loaded to the volatile 
memory when the controller is started. 
The parameter values in the nonvolatile memory are also referred to as 
"startup values" in the PC software from PI. 

Positioner 

Mechanics connected to the C-863.12. In the case of positioners with 
just one motion axis, the designation "axis" is synonymous with 
"positioner". Positioners that allow motion in several axes are also 
designated as "multi-axis positioners". For these positioners, a 
distinction must be made between the individual axes. 
In this manual, actuators, i.e., drive components without a motion 
platform (e.g., precision linear actuators), are designated as positioners 
as well. 

Control value 

The control value is the input for the PWM converter of the C-863.12. 
The PWM converter converts the control value into the PWM signal for 
the axis of the positioner. 

  

 

1.4

 

Figures 

For better understandability, the colors, proportions, and degree of detail in illustrations can 
deviate from the actual circumstances. Photographic illustrations may also differ and must not 
be seen as guaranteed properties. 

 

 

1.5

 

Other Applicable Documents 

The devices and software tools from PI mentioned in this documentation are described in 
separate manuals. 

 

Description 

Document 

Short instructions for the installation and 
startup of the C-863.12 

MS242EK Short Instructions for Digital Motor 
Controllers 

PI GCS driver library for use with NI LabVIEW 
software 

SM158E Software Manual 

PI MATLAB Driver GCS 2.0 

SM155E Software Manual 

PI GCS 2.0 DLL 

SM151E Software Manual 

GCS array 

SM146E Software Manual 

Содержание MS249E
























































































































































































































































































Отзывы:

Нет отзывов