PI MS249E Скачать руководство пользователя страница 249

Страница: 249 / 279

9 Adapting Settings

C-863.12 Mercury Controller

MS249E

Version: 1.2.1

243

Type

Element Parameter name

Description

For details, see "On-Target State" (p.
23).

0x3C

CHAR

Axis

Stage Name

Positioner name
Maximum 20 characters; default
value: DEFAULT_STAGE

0x3F

FLOAT

Axis

Settling Time (s)

Delay time for setting the on-target
state.
For details, see "On-Target State" (p.
23).

0x47

INT

Axis

Reference Travel
Direction

Default direction for the reference
move
For details, see "Referencing" (p.
28).

0x48

INT

Axis

Motor Drive Offset

Velocity-dependent offset
For details, see "Servo Algorithm
and Other Control Value
Corrections" (p. 21).

0x49

FLOAT

Axis

Closed-Loop
Velocity (Phys.
Unit/s)

Velocity in closed-loop operation
Limited by parameter 0xA
For details, see "Generation of
Dynamics Profile" (p. 18).

0x4A

FLOAT

Axis

Maximum Closed-
Loop Acceleration
(Phys. Unit/s

)

Maximum acceleration in closed-
loop operation
Specifies the maximum value for
parameter 0xB.

0x4B

FLOAT

Axis

Maximum Closed-
Loop Deceleration
(Phys. Unit/s

)

Maximum deceleration in closed-
loop operation
Specifies the maximum value for
parameter 0xC.

0x50

FLOAT

Axis

Velocity For
Reference Moves
(Phys. Unit/s)

Velocity for reference move
For details, see "Referencing" (p.
28).

0x5A

INT

Axis

Numerator Of The
Servo Loop Input
Factor

Numerator and denominator of the
servo-loop input factor
For details, see "Servo Algorithm
and Other Control Value
Corrections" (p. 21).

0x5B

INT

Axis

Denominator Of The
Servo Loop Input
Factor

0x5C

INT

Axis

Source Of Reference
Signal

Reference signal source for the

FRF

FED

commands

For details, see "Commands and

Содержание MS249E
























































































































































































































































































Результаты поиска

Содержание MS249E

Отзывы:

PI MS249E, Руководство пользователя, Страница: 249 / 279

Результаты поиска

Содержание MS249E

Отзывы: