manualshive.com logo in svg

PI MS249E, Руководство пользователя, Страница: 64 / 279

Поделиться
Скачать
PI MS249E Скачать руководство пользователя страница 64

 

 

6 Startup 

58 

Version: 1.2.1 

MS249E 

C-863.12 Mercury Controller 

6.4.3

 

Establishing Communication for Networked Controllers 

The following describes the procedure for PIMikroMove and for PITerminal. 

 

 

INFORMATION 

 

If you are establishing communication with a networked controller via PITerminal, the address 
of the controller to be addressed is required in every command line. See "Target and Sender 
Address" (p. 117) for details. 

➢

 

Use PITerminal to test communication with networked controllers. 

  

 

INFORMATION 

 

The RS-232 output lines of some PCs are not adapted for the maximum number of 16 
controllers in a network. If you have connected a daisy chain network to such a PC via the RS-
232 interface, communication malfunctions may occur (e.g., timeout). In case of 
communication malfunctions: 
1.

 

Disconnect the null-modem cable from the 

RS-232 In

 socket of the controller which is 

connected to the PC. 

2.

 

Connect the daisy chain network to the PC via the USB interface of this controller. 

Requirements 

✓

 

You have read and understood the general notes on startup (p. 51). 

✓

 

You have set up a daisy chain network . 

✓

 

You have assigned  (p. 52)a unique address to each of the networked controllers. 

✓

 

You have set (p. 53) the same baud rate for all controllers. 

✓

 

All controllers in the daisy chain network are switched on (p. 53). 

✓

 

The PC is switched on. 

✓

 

The required software is installed on the PC (p. 39). 

✓

 

If you have connected the first controller in the chain to the PC via the USB interface: 
The USB drivers are installed on the PC (p. 39). 

✓

 

You have read and understood the manual for the PC software. The links to the 
software manuals are in the A000T0081 file on the PI software data storage medium. 

 

Establishing communication with PIMikroMove 

1.

 

Start PIMikroMove. 

The 

Start up controller

 window opens with the 

Connect controller

 step.  

−

 

If the 

Start up controller

 window does not automatically open, select the 

Connections > New...

 menu item in the main window. 

Содержание MS249E
























































































































































































































































































Отзывы:

Нет отзывов