PI MS249E Скачать руководство пользователя страница 233

Страница: 233 / 279

8 GCS Commands

C-863.12 Mercury Controller

MS249E

Version: 1.2.1

227

-1083

PI_WRONG_DATA_TYPE

A function argument has an
unexpected data type.

-1084

PI_DIFFERENT_ARRAY_SIZES

Length of data arrays is
different.

-1085

PI_PARAM_NOT_FOUND_IN_PARAM_DAT
_FILE

Parameter value not found in
parameter DAT file.

-1086

PI_MACRO_RECORDING_NOT_ALLOWED_I
N_THIS_MODE

Macro recording is not
allowed in this mode of
operation.

-1087

PI_USER_CANCELLED_COMMAND

Command cancelled by user
input.

-1088

PI_TOO_FEW_GCS_DATA

Controller sent too few GCS
data sets

-1089

PI_TOO_MANY_GCS_DATA

Controller sent too many GCS
data sets

-1090

PI_GCS_DATA_READ_ERROR

Communication error while
reading GCS data

-1091

PI_WRONG_NUMBER_OF_INPUT_ARGUM
ENTS

Wrong number of input
arguments.

-1092

PI_FAILED_TO_CHANGE_CCL_LEVEL

Change of command level has
failed.

-1093

PI_FAILED_TO_SWITCH_OFF_SERVO

Servo mode has failed to
switch off.

-1094

PI_FAILED_TO_SET_SINGLE_PARAMETER_
WHILE_PERFORMING_CST

A parameter could not be set
while performing CST: CST
was not performed
(parameters remain
unchanged).

-1095

PI_ERROR_CONTROLLER_REBOOT

Connection could not be
reestablished after reboot.

-1096

PI_ERROR_AT_QHPA

Sending HPA? or receiving the
response has failed.

-1097

PI_QHPA_NONCOMPLIANT_WITH_GCS

HPA? response does not
comply with GCS2 syntax.

-1098

PI_FAILED_TO_READ_QSPA

Response to SPA? could not
be received. Response to
SPA? could not be received.

-1099

PI_PAM_FILE_WRONG_VERSION

Version of PAM file cannot be
handled (too old or too new)

-1100

PI_PAM_FILE_INVALID_FORMAT

PAM file does not contain
required data in PAM-file
format

-1101

PI_INCOMPLETE_INFORMATION

Information does not contain
all required data

Содержание MS249E
























































































































































































































































































Результаты поиска

Содержание MS249E

Отзывы:

PI MS249E, Руководство пользователя, Страница: 233 / 279

Результаты поиска

Содержание MS249E

Отзывы: