manualshive.com logo in svg

PI MS249E, Руководство пользователя, Страница: 219 / 279

Поделиться
Скачать
PI MS249E Скачать руководство пользователя страница 219

 

 

8 GCS Commands 

C-863.12 Mercury Controller 

MS249E 

Version: 1.2.1 

213 

309 

PI_CNTR_MACRO_OUT_OF_SPACE 

Insufficient space to store 
macro 

310 

PI_CNTR_EUI_OLDVERSION_CFGDATA 

Configuration data has old 
version number 

311 

PI_CNTR_EUI_INVALID_CFGDATA 

Invalid configuration data 

333 

PI_CNTR_HARDWARE_ERROR 

Internal hardware error 

400 

PI_CNTR_WAV_INDEX_ERROR 

Wave generator index error 

401 

PI_CNTR_WAV_NOT_DEFINED 

Wave table not defined  

402 

PI_CNTR_WAV_TYPE_NOT_SUPPORTED 

Wave type not supported 

403 

PI_CNTR_WAV_LENGTH_EXCEEDS_LIMIT 

Wave length exceeds limit 

404 

PI_CNTR_WAV_PARAMETER_NR 

Wave parameter number 
error 

405 

PI_CNTR_WAV_PARAMETER_OUT_OF_LI
MIT 

Wave parameter out of range 

406 

PI_CNTR_WGO_BIT_NOT_SUPPORTED 

WGO command bit not 
supported 

500 

PI_CNTR_EMERGENCY_STOP_BUTTON_AC
TIVATED 

The \"red knob\" is still set 
and disables system 

501 

PI_CNTR_EMERGENCY_STOP_BUTTON_W
AS_ACTIVATED 

The \"red knob\" was 
activated and still disables 
system - reanimation 
required 

502 

PI_CNTR_REDUNDANCY_LIMIT_EXCEEDED  Position consistency check 

failed 

503 

PI_CNTR_COLLISION_SWITCH_ACTIVATED  Hardware collision sensor(s) 

are activated 

504 

PI_CNTR_FOLLOWING_ERROR 

Strut following error 
occurred, e.g. caused by 
overload or encoder failure 

505 

PI_CNTR_SENSOR_SIGNAL_INVALID 

One sensor signal is not valid 

506 

PI_CNTR_SERVO_LOOP_UNSTABLE 

Servo loop was unstable due 
to wrong parameter setting 
and switched off to avoid 
damage. 

507 

PI_CNTR_LOST_SPI_SLAVE_CONNECTION 

Digital connection to external 
SPI slave device is lost 

508 

PI_CNTR_MOVE_ATTEMPT_NOT_PERMITT
ED 

Move attempt not permitted 
due to customer or limit 
settings 

509 

PI_CNTR_TRIGGER_EMERGENCY_STOP 

Emergency stop caused by 
trigger input 

530 

PI_CNTR_NODE_DOES_NOT_EXIST 

A command refers to a node 
that does not exist 

Содержание MS249E
























































































































































































































































































Отзывы:

Нет отзывов