manualshive.com logo in svg

PI MS249E, Руководство пользователя, Страница: 69 / 279

Поделиться
Скачать
PI MS249E Скачать руководство пользователя страница 69

 

 

6 Startup 

C-863.12 Mercury Controller 

MS249E 

Version: 1.2.1 

63 

  

 

NOTICE 

 

Oscillation! 

Unsuitable setting of the C-863.12's servo control parameters can cause the positioner to 
oscillate. Oscillation can damage the positioner and/or the load fixed to it. 

➢

 

Secure the positioner and all loads adequately. 

➢

 

If the Positioner is oscillating (unusual operating noise), immediately switch off the servo 
mode or disconnect the C-863.12 from the power source. 

➢

 

Only switch on the servo mode after you have modified the servo control parameter 
settings of the C-863.12; see "Optimizing Servo Control Parameters" (p. 66). 

➢

 

If, due to a very high load, oscillation occurs during the reference move, follow the 
instructions for the reference move in "Troubleshooting" (p. 255). 

  

 

INFORMATION 

 

The C-863.12 has a nonvolatile memory for parameter values. Therefore, after switching on, 
the correct parameter settings for the connected positioner may already be loaded. 

➢

 

However, if you have loaded a parameter set from the positioner database and 
overwritten the original settings of the C-863.12 in the volatile memory during the process, 
avoid saving the new settings in the nonvolatile memory of the C-863.12. The original 
settings are active again after the C-863.12 has been switched off and on again or been 
rebooted. 

➢

 

If you are using the 

Start up controller

 window in PIMikroMove for selecting the positioner 

and you are asked how you want to save the new settings, click the 

Save all settings 

permanently on controller

 button only if you are sure that the C-863.12 is working 

correctly with the settings. 

  

 

INFORMATION 

 

If the 

Select connected stages

 step is not displayed in PIMikroMove, the controller has 

probably already loaded the correct parameter settings for the positioner type connected. 
1.

 

Check 

Start up axes

 step to ensure that the correct positioner type is in the 

Stage

 column 

in the middle of the window. 

2.

 

If the positioner type is not correct, click 

Select connected stages

 in the left area of the 

Start up controller

 window to change the positioner type. 

Requirements 

✓

 

You have read and understood the general notes on startup (p. 51). 

✓

 

PIMikroMove is installed on the PC (p. 39). 

✓

 

You have read and understood the PIMikroMove manual. The links to the software 
manuals are in the A000T0081 file on the PI software data storage medium. 

Содержание MS249E
























































































































































































































































































Отзывы:

Нет отзывов