PI MS249E Скачать руководство пользователя страница 217

Страница: 217 / 279

8 GCS Commands

C-863.12 Mercury Controller

MS249E

Version: 1.2.1

211

PI_CNTR_DIO_AND_TRACING_NOT_POSSI
BLE

No tracing possible while
digital IOs are used on this
HW revision. Reconnect to
switch operation mode.

PI_CNTR_COLLISION

Move not possible, would
cause collision

PI_CNTR_SLAVE_NOT_FAST_ENOUGH

Stage is not capable of
following the master. Check
the gear ratio.

PI_CNTR_CMD_NOT_ALLOWED_WHILE_A
XIS_IN_MOTION

This command is not allowed
while the affected axis or its
master is in motion.

PI_CNTR_OPEN_LOOP_JOYSTICK_ENABLE
D

Servo cannot be switched on
when open-loop joystick
control is activated.

PI_CNTR_INVALID_SERVO_STATE_FOR_PA
RAMETER

This parameter cannot be
changed in current servo
mode.

PI_CNTR_UNKNOWN_STAGE_NAME

Unknown stage name

PI_CNTR_INVALID_VALUE_LENGTH

Invalid length of value (too
much characters)

PI_CNTR_AUTOZERO_FAILED

AutoZero procedure was not
successful

PI_CNTR_SENSOR_VOLTAGE_OFF

Sensor voltage is off

100

PI_LABVIEW_ERROR

PI driver for use with NI
LabVIEW reports error. See
source control for details.

200

PI_CNTR_NO_AXIS

No stage connected to axis

201

PI_CNTR_NO_AXIS_PARAM_FILE

File with axis parameters not
found

202

PI_CNTR_INVALID_AXIS_PARAM_FILE

Invalid axis parameter file

203

PI_CNTR_NO_AXIS_PARAM_BACKUP

Backup file with axis
parameters not found

204

PI_CNTR_RESERVED_204

PI internal error code 204

205

PI_CNTR_SMO_WITH_SERVO_ON

SMO with servo on

206

PI_CNTR_UUDECODE_INCOMPLETE_HEAD
ER

uudecode: incomplete header

207

PI_CNTR_UUDECODE_NOTHING_TO_DEC
ODE

uudecode: nothing to decode

208

PI_CNTR_UUDECODE_ILLEGAL_FORMAT

uudecode: illegal UUE format

209

PI_CNTR_CRC32_ERROR

CRC32 error

210

PI_CNTR_ILLEGAL_FILENAME

Illegal file name (must be 8-0
format)

Содержание MS249E
























































































































































































































































































Результаты поиска

Содержание MS249E

Отзывы:

PI MS249E, Руководство пользователя, Страница: 217 / 279

Результаты поиска

Содержание MS249E

Отзывы: