PI MS249E Скачать руководство пользователя страница 79 | Manualshive

Страница: 79 / 279

PI MS249E Скачать руководство пользователя страница 79

7 Operation

C-863.12 Mercury Controller

MS249E

Version: 1.2.1

73

7.1

Motion Errors

7.1.1

Behavior with Motion Errors

Motion errors can be caused for example, by malfunctions of the drive or the position sensor of
the positioner.

A motion error occurs, when the position error (i.e., the absolute value of the difference
between the current position and the commanded position) exceeds the specified maximum
value in closed-loop operation. The range in which the deviation may lie is specified by the

Maximum Position Error (Phys. Unit)

parameter (ID 0x8).

If motion error occurs, the C-863.12 reacts as follows to protect the system against damage:

▪

The servo mode is switched off for the axis in question.

▪

If applicable, the brake is activated for the axis in question.

▪

All motion is stopped.

▪

Error code -1024 is set.

Figure 20: Behavior in case of motion errors

7

Operation

«
...
77
78
79
80
81
...
»

Содержание MS249E
























































































































































































































































































Отзывы:

Нет отзывов