PI MS249E Скачать руководство пользователя страница 53 | Manualshive

Страница: 53 / 279

PI MS249E Скачать руководство пользователя страница 53

5 Installation

C-863.12 Mercury Controller

MS249E

Version: 1.2.1

47

5.6

Connecting the Power Supply to the C-863.12

INFORMATION

If the positioner is equipped with a PWM amplifier that is supplied via a separate power
adapter:

➢

To achieve the optimum motor performance, use a power adapter for the C-863.12 that
supplies the same output voltage as the power adapter for the PWM amplifier.

Requirements

✓

The power cord is

not

connected to the power socket.

Tools and accessories

▪

Wide input range power supply (p. 9) included, for line voltages between 100 and 240
volts alternating voltage at 50 or 60 Hz

▪

Alternative: Sufficiently rated power adapter

▪

Power cord supplied

▪

Alternative: Sufficiently sized power cord

Connecting the power adapter to the C-863.12

➢

Connect the 4-pin connector of the power adapter to the

48 V 2 A

socket of the C-

863.12.

−

Make sure that the connector is locked in the socket.

➢

Connect the power cord to the power adapter.

«
...
51
52
53
54
55
...
»

Содержание MS249E
























































































































































































































































































Отзывы:

Нет отзывов