PI MS249E Скачать руководство пользователя страница 218

Страница: 218 / 279

8 GCS Commands

212

Version: 1.2.1

MS249E

C-863.12 Mercury Controller

211

PI_CNTR_FILE_NOT_FOUND

File not found on controller

212

PI_CNTR_FILE_WRITE_ERROR

Error writing file on controller

213

PI_CNTR_DTR_HINDERS_VELOCITY_CHAN
GE

VEL command not allowed in
DTR Command Mode

214

PI_CNTR_POSITION_UNKNOWN

Position calculations failed

215

PI_CNTR_CONN_POSSIBLY_BROKEN

The connection between
controller and stage may be
broken

216

PI_CNTR_ON_LIMIT_SWITCH

The connected stage has
driven into a limit switch,
some controllers need CLR to
resume operation

217

PI_CNTR_UNEXPECTED_STRUT_STOP

Strut test command failed
because of an unexpected
strut stop

218

PI_CNTR_POSITION_BASED_ON_ESTIMATI
ON

While MOV! is running
position can only be
estimated!

219

PI_CNTR_POSITION_BASED_ON_INTERPOL
ATION

Position was calculated during
MOV motion

220

PI_CNTR_INTERPOLATION_FIFO_UNDERR
UN

FIFO buffer underrun during
interpolation

221

PI_CNTR_INTERPOLATION_FIFO_OVERFLO
W

FIFO buffer overflow during
interpolation

230

PI_CNTR_INVALID_HANDLE

Invalid handle

231

PI_CNTR_NO_BIOS_FOUND

No bios found

232

PI_CNTR_SAVE_SYS_CFG_FAILED

Save system configuration
failed

233

PI_CNTR_LOAD_SYS_CFG_FAILED

Load system configuration
failed

301

PI_CNTR_SEND_BUFFER_OVERFLOW

Send buffer overflow

302

PI_CNTR_VOLTAGE_OUT_OF_LIMITS

Voltage out of limits

303

PI_CNTR_OPEN_LOOP_MOTION_SET_WH
EN_SERVO_ON

Open-loop motion attempted
when servo ON

304

PI_CNTR_RECEIVING_BUFFER_OVERFLOW Received command is too

long

305

PI_CNTR_EEPROM_ERROR

Error while reading/writing
EEPROM

306

PI_CNTR_I2C_ERROR

Error on I2C bus

307

PI_CNTR_RECEIVING_TIMEOUT

Timeout while receiving
command

308

PI_CNTR_TIMEOUT

A lengthy operation has not
finished in the expected time

Содержание MS249E
























































































































































































































































































Результаты поиска

Содержание MS249E

Отзывы:

PI MS249E, Руководство пользователя, Страница: 218 / 279

Результаты поиска

Содержание MS249E

Отзывы: