PI MS249E Скачать руководство пользователя страница 138 | Manualshive

Страница: 138 / 279

PI MS249E Скачать руководство пользователя страница 138

8 GCS Commands

132

Version: 1.2.1

MS249E

C-863.12 Mercury Controller

MAC START Test 10 50

Meaning of the variables here:

$1: Delay in ms between each step in the STEPS macro. The
value is incremented by 10 by the TEST macro until it
reaches 110.

$2: Number of repetitions of the whole "flashing light"
procedure.

BRA (Set Brake Activation State)

Description:

Activates/deactivates brake for specified axes.

Format:

BRA {<AxisID> <BrakeState>}

Arguments:

<AxisID> is one axis of the controller

<BrakeState> can have the following values:
0 = Brake deactivated
1 = Brake activated

Response:

None

Troubleshooting: Illegal axis identifier

Notes:

The brake can only be used if parameter 0x1A (

Has Brake?

)

has the value 1 ("yes").
If parameter 0x1A (

Has Brake?

) has the value 1 ("yes"), the

following applies:

▪

The brake can be activated or deactivated with BRA
only if the servo mode is switched off. Secure the
positioner against moving unintentionally before you
deactivate the brake before you deactivate the brake
with BRA!

▪

Setting the servo mode with SVO (p. 195) influences
the activation state of the brake:

−

Switching servo mode on deactivates the brake.

−

Switching servo mode off activates the brake.

▪

If a motion error occurs (p. 73), the servo mode is
switched off and the brake is activated.

If the integrated brake driver of the C-863.12 is to be used,
parameter 0x3094 (

Internal Brake

) must also have the

value 1. Refer the descriptions in "Parameter Overview" (p.
239) for further information.

«
...
136
137
138
139
140
...
»

Содержание MS249E
























































































































































































































































































Отзывы:

Нет отзывов