PI MS249E Скачать руководство пользователя страница 215

Страница: 215 / 279

8 GCS Commands

C-863.12 Mercury Controller

MS249E

Version: 1.2.1

209

PI_CNTR_OPM_NOT_INITIALIZED

OPM (Optical Power Meter)
not initialized or cannot be
initialized

PI_CNTR_OPM_COM_ERROR

OPM (Optical Power Meter)
Communication Error

PI_CNTR_MOVE_TO_LIMIT_SWITCH_FAILE
D

Move to limit switch failed

PI_CNTR_REF_WITH_REF_DISABLED

Attempt to reference axis
with referencing disabled

PI_CNTR_AXIS_UNDER_JOYSTICK_CONTRO
L

Selected axis is controlled by
joystick

PI_CNTR_COMMUNICATION_ERROR

Controller detected
communication error

PI_CNTR_DYNAMIC_MOVE_IN_PROCESS

MOV! motion still in progress

PI_CNTR_UNKNOWN_PARAMETER

Unknown parameter

PI_CNTR_NO_REP_RECORDED

No commands were recorded
with REP

PI_CNTR_INVALID_PASSWORD

Password invalid

PI_CNTR_INVALID_RECORDER_CHAN

Data Record Table does not
exist

PI_CNTR_INVALID_RECORDER_SRC_OPT

Source does not exist;
number too low or too high

PI_CNTR_INVALID_RECORDER_SRC_CHAN Source Record Table number

too low or too high

PI_CNTR_PARAM_PROTECTION

Protected Param: current
Command Level (CCL) too low

PI_CNTR_AUTOZERO_RUNNING

Command execution not
possible while Autozero is
running

PI_CNTR_NO_LINEAR_AXIS

Autozero requires at least one
linear axis

PI_CNTR_INIT_RUNNING

Initialization still in progress

PI_CNTR_READ_ONLY_PARAMETER

Parameter is read-only

PI_CNTR_PAM_NOT_FOUND

Parameter not found in non-
volatile memory

PI_CNTR_VOL_OUT_OF_LIMITS

Voltage out of limits

PI_CNTR_WAVE_TOO_LARGE

Not enough memory available
for requested wave curve

PI_CNTR_NOT_ENOUGH_DDL_MEMORY

Not enough memory available
for DDL table; DDL can not be
started

PI_CNTR_DDL_TIME_DELAY_TOO_LARGE

Time delay larger than DDL
table; DDL can not be started

Содержание MS249E
























































































































































































































































































Результаты поиска

Содержание MS249E

Отзывы:

PI MS249E, Руководство пользователя, Страница: 215 / 279

Результаты поиска

Содержание MS249E

Отзывы: