PI MS249E Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 279

PI MS249E Скачать руководство пользователя страница 8

1 About this Document

2

Version: 1.2.1

MS249E

C-863.12 Mercury Controller

Symbol/Label

Meaning

Warning sign on the product referring to detailed
information in this manual.

Start > Settings

Menu path in the PC software (example: to open the
menu, the

Start

and

Settings

menu items must be

clicked in succession)

POS?

Command line or a command from PI's General
Command Set (GCS) (example: Command to get the
axis position).

Device S/N

Parameter name (example: Parameter where the serial
number is stored)

5

Value that must be entered or selected via the PC
software

1.3

Definition of Terms

Term

Explanation

Axis

Also referred to as "logical axis". The logical axis represents the motion
of the mechanics in the firmware of the C-863.12. For mechanics that
allow motion in several directions (e.g., in X, Y, and Z), each direction of
motion corresponds to a logical axis.

Daisy chain

Wiring diagram by which one controller is connected to the next in
sequence (series connection principle). Here the first controller is
connected directly to the PC. The additional controllers are always
connected to the ones that precede them so that a chain is formed.
The signal to and from a controller goes to the PC via the previous
controllers.

Dynamics profile

Comprises the target position, velocity, and acceleration of the axis
calculated by the profile generator of the C-863.12 for any point in
time of the motion. The calculated values are called "commanded
values".

Firmware

Software that is installed on the controller.

Volatile memory

RAM module where the parameters are saved when the controller is
switched on (working memory). The parameter values in the volatile
memory determine the current behavior of the system.
The parameter values in the volatile memory are also referred to as
"Active Values" in the PC software from PI.

GCS

PI General Command Set; command set for PI controllers. Piezo drivers
and servo controllers can be operated together with minimal
programming effort thanks to GCS.

Incremental position
sensor

Sensor (encoder) for detecting changes of position or changes of angle.
Signals from the incremental position sensor are used for axis position

«
...
6
7
8
9
10
...
»

Содержание MS249E
























































































































































































































































































Отзывы:

Нет отзывов