manualshive.com logo in svg

PerkinElmer Lambda 650, Руководство по оборудованию

Поделиться
Скачать
PerkinElmer Lambda 650 Скачать руководство пользователя страница 65

Lambda 650/850/950 Hardware Guide . 65 

 

 

 

Accessory Installation 

 

 

WARNING 

Electrical Hazard 

To prevent potential injury to yourself and damage to the instrument, 

switch 

OFF

 all instruments in the system and disconnect them from the 

line power supply before you alter, or make any new, electrical 

connections. 

NOTE:  

To operate the spectrometer with some accessories, for example Peltier cell changers, you 

need an accessory printed circuit board (PCB) fitted in the connector panel. The accessory 

PCB will be installed by a PerkinElmer service engineer. 

This section of the manual details changes that may need to be made to the basic 

spectrometer before installing an accessory and an overview of the installation required for 

some of the specific accessories.  Full procedures for installing the accessories in the 

spectrometer are described in the directions provided with the respective accessories.  

Removing the parts of the Sample Compartment 

Removing the Sample Compartment Cover 

1.

 

Open the sample compartment cover so that the lid is at 90 degrees. 

2.

 

Push back on the base of the lid to release the three lugs holding it in place. 

 

3.

 

Lift the whole lid vertically to remove. 

NOTE:  

 To re-fit the lid, make sure the lugs are properly inserted into the holes and then holding the 

lid vertically, pull it towards the front the instrument making sure the lugs are fully locked 

into place.  

Содержание Lambda 650









































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды