PerkinElmer Lambda 650 Скачать руководство пользователя страница 60

Страница: 60 / 72

60 . Maintenance

Replacing a Lamp

If a lamp failure warning message is displayed, or you are seeing excessive noise on the

baseline, you can replace the lamps as follows.

WARNING

Electrical Hazard

High voltages are present at the lamp connectors in the lamp

compartment – severe electric shock hazard.

Never unplug or plug in a lamp cable while power is ON.

Switch off the spectrometer and remove the plug from the electrical

supply before starting with the replacement.

High Temperatures - Risk of Burns

Lamps soon become very hot, make sure that the lamps and the lamp

compartment have cooled to room temperature before you touch them.

UV Radiation

The lamps emit intense UV radiation which can damage your eyes.

Do not open the lamp compartment when the lamps are on.

Do not gaze into a lighted lamp.

The source lamps are located in the lamp compartment at the top left rear of the

spectrometer, as shown in Figure 18.

Figure 18 Lamp compartment

Lamp compartment

Содержание Lambda 650









































































Результаты поиска

Содержание Lambda 650

Отзывы:

Бренды по названию

Популярные бренды

PerkinElmer Lambda 650, Руководство по оборудованию

Результаты поиска

Содержание Lambda 650

Отзывы:

Бренды по названию

Популярные бренды