PerkinElmer Lambda 650 Скачать руководство пользователя страница 15

Страница: 15 / 72

Lambda 650/850/950 Hardware Guide . 15

Environmental Conditions

The instrument has been designed to be safe under the following conditions:

•

Indoor use

•

Altitude up to 2000 m

•

Ambient temperatures of 5

C to 40

•

A maximum ambient relative humidity of 80% for temperatures up to 31

C, decreasing

linearly to 50% relative humidity at 40

•

Mains fluctuations not exc 10% of the nominal voltage.

WARNING

This instrument is not designed for operation in an explosive

atmosphere.

Other Environmental Conditions

Chemicals

Use, store, and dispose of chemicals that you require for your analyses in accordance with

the manufacturer’s recommendations and local safety regulations.

WARNING

Hazardous Chemicals

Some chemicals used with this instrument may be hazardous or may

become hazardous after completion of an analysis.
The responsible body (for example, Laboratory Manager) must take

the necessary precautions to ensure that the surrounding workplace

and instrument operators are not exposed to hazardous levels of toxic

substances (chemical or biological) as defined in the applicable

Material Safety Data Sheets (MSDS) or OSHA, ACGIH, or COSHH

documents.
Venting for fumes and disposal of waste must be in accordance with

all national, state and local health and safety regulations and laws.

OSHA: Occupational Safety and Health Administration (U.S.A.)

ACGIH: American Conference of Governmental Industrial Hygienists (U.S.A)

COSHH: Control of Substances Hazardous to Health (U.K.)

Содержание Lambda 650









































































Результаты поиска

Содержание Lambda 650

Отзывы:

Бренды по названию

Популярные бренды

PerkinElmer Lambda 650, Руководство по оборудованию

Результаты поиска

Содержание Lambda 650

Отзывы:

Бренды по названию

Популярные бренды