manualshive.com logo in svg

PerkinElmer Lambda 650, Руководство по оборудованию

Поделиться
Скачать
PerkinElmer Lambda 650 Скачать руководство пользователя страница 50

50 . Using the Instrument 

 

5.

 

Make horizontal fine alignment to the sample cell holder (locking screws and milled 

posts loosened) to obtain the highest possible transmittance reading on the display. 
Close sample compartment cover while measuring transmittance. 

6.

 

Make fine alignment using the vertical adjustment screw again to obtain the highest 

possible reading. 
Close sample compartment cover while measuring transmittance. 

7.

 

When you are satisfied with the alignment, tighten the milled posts and the locking 

screws on the cell holder. 

8.

 

Reinstall the reference cell in the reference cell holder. 

9.

 

The sample cell remains in its holder. 

10.

 

Repeat steps 4 to 6 with the reference cell holder, but this time obtain the lowest 

possible transmittance reading on the display. 
This completes the fine alignment procedure.   

NOTE:   

When the cell holder has been aligned once, you can take it out and reinstall it without 

aligning it again. 

Minimum Volume Applications 

To measure minimum sample volumes, use microcells (offered by PerkinElmer). 

The minimum sample volume required is a function of the cell internal width or volume and 
is specified below. 

 

Содержание Lambda 650









































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды