PerkinElmer Lambda 650 Скачать руководство пользователя страница 14

Страница: 14 / 72

14 . Safety Practices

General Operating Conditions

The Lambda 650/850/950

has been designed and tested in accordance with PerkinElmer

specifications and in accordance with the safety requirements of the International

Electrotechnical Commission (IEC). The Lambda 650/850/950

conforms to IEC61010-1

(Safety Requirements for electrical equipment for measurement, control and laboratory use)

as it applies to IEC Class 1 (earthed) appliances and therefore meets the requirements of EC

directive 73/23/EEC.

This instrument meets the Canadian Standards Association (CSA) Standard CAN/CSA-C22.2

No. 1010.1-92:

Laboratory Equipment.

Only use the Lambda 650/850/950

indoors and under the following conditions:

Temperature

C to 35

Relative Humidity

80% maximum (non-condensing)

If possible, avoid any adjustment, maintenance and repair of the opened, operating
instrument. If any adjustment, maintenance and repair of the opened instrument is

necessary, this must be done by a skilled person who is aware of the hazard involved.

Whenever it is likely that the Lambda 650/850/950

is unsafe, make it inoperative. The

Lambda 650/850/950

may be unsafe if it:

•

shows visible damage

•

fails to perform the intended measurement

•

has been subjected to prolonged storage in unfavorable conditions

•

has been subjected to severe transport stresses.

NOTE:

The instrument must always be positioned so that it can easily be disconnected from the

power supply.

Содержание Lambda 650









































































Результаты поиска

Содержание Lambda 650

Отзывы:

Бренды по названию

Популярные бренды

PerkinElmer Lambda 650, Руководство по оборудованию

Результаты поиска

Содержание Lambda 650

Отзывы:

Бренды по названию

Популярные бренды