PerkinElmer Lambda 650 Скачать руководство пользователя страница 47

Страница: 47 / 72

Lambda 650/850/950 Hardware Guide . 47

The Single Cell Holder

Description

There are two single-cell holders provided with the instrument, one for the sample beam and

one for the reference beam. The single-cell holders are mounted on a plinth to bring them in
line with the radiation beam.

Figure 12 Single Cell Holder B0505071

Installing the Cell Holder

Install the plinth in the sample compartment as follows:

Lower the plinth so that the two locating holes slip onto the two locating pins on the

baseplate in the sample compartment, as shown in Figure 13.
The plinth only fits one way round.

Figure 13 Fitting the plinth to the baseplate in the sample compartment

Screw the two thumbscrews by hand into the baseplate.

Install the single-cell holder in the sample compartment as follows:

Orientate the holder so that the word

LAMBDA

is toward the front of the sample

compartment (see Figure 14 below).

Lower the holder so that the two locating holes slip onto the two studs on the two
locating pins on the plinth in the sample compartment.

Locating Pin

Thumbscrew

Locating Pin

Locking screw
for horizontal
alignment

Vertical adjustment
screw

Milled post

Lifter

Locking screw
for horizontal
alignment

Содержание Lambda 650









































































Результаты поиска

Содержание Lambda 650

Отзывы:

Бренды по названию

Популярные бренды

PerkinElmer Lambda 650, Руководство по оборудованию

Результаты поиска

Содержание Lambda 650

Отзывы:

Бренды по названию

Популярные бренды