PerkinElmer Lambda 650 Скачать руководство пользователя страница 41

Страница: 41 / 72

Lambda 650/850/950 Hardware Guide . 41

10.

Enter a

Name

for the instrument.

The

Name

you enter will be displayed in the Explorer beneath the instrument icon. It

can be edited in future if required.

11.

Select whether a

Common Beam Depolarizer

Double Polarizer / Depolarizer

and/or manual

Attenuators

are installed.

These can be selected if you are going to use them, even if they are not currently

installed.

NOTE:

Manual Attenuators are only available for the Lambda 650, the Lambda 850 and 950 have

automatic attenuators. The Common Beam Depolarizer requires a firmware command to be

enabled.

12.

Click

Next

The Finished page displays all the selected settings.

13.

If all the settings are correct, click

Finish

to close the wizard and add the instrument.

The Wizard closes, a confirmation message that the instrument has been successfully

installed is displayed, and the instrument is displayed in the Explorer.

Click

Back

to return to the previous page(s) and amend the settings as required.

Содержание Lambda 650









































































Результаты поиска

Содержание Lambda 650

Отзывы:

Бренды по названию

Популярные бренды

PerkinElmer Lambda 650, Руководство по оборудованию

Результаты поиска

Содержание Lambda 650

Отзывы:

Бренды по названию

Популярные бренды