PerkinElmer Lambda 650 Скачать руководство пользователя страница 42

Страница: 42 / 72

42 . Lambda 650 Installation

Calibrating the Instrument

Once the instrument is set up in the software you will need to calibrate it.

NOTE:

Make sure that the instrument has been switched on for at least an hour before calibrating it.

14.

From the Instruments page of the Explorer, right-click on the new instrument and select

Calibrate

The Calibration Utility dialog is displayed.
The dialog displays the names of the routines, a description, the last calibration date of
the routine, and whether the test is enabled.

15.

To view (and change) the settings for a particular routine, highlight the routine in the

table and then click

Settings

The settings dialog for the selected routine is displayed.

NOTE:

Settings is not available for Slit Calibration.

16.

Select the routines to be performed by the calibration.
There are three calibration routines available -

UV/Vis Two Peak

(see page 42 for

details),

Slit Calibration

, and

0%T

(see page 43 for details). All of these routines

should be performed.
A check mark indicates the routine is selected and will be performed.

17.

Click

Calibrate

The calibrations are performed in the order listed in the table. Messages below the table

show the progress of the calibration.
When a calibration has passed, a green check mark is displayed in the first column of

the table. If the test fails, a red cross is displayed. In such an event please contact your

local PerkinElmer Service Representative.

18.

When the calibration has finished, click

Close

to close the dialog.

The date and time of the calibration is recorded in the instrument event log.

NOTE:

It is not possible to print the calibration results.

Your instrument is now ready to be used.

UV/Vis Two Peak Calibration

This calibrates the UV/Vis wavelength range.

Select

Manual set

Manual set 1 peak

Manual set 2 peaks

Auto search 1 peak

Auto search 2 peaks

•

Manual set

enables you to enter the

offset

and

factor

(without the need to

determine the values in advance).

•

Manual set 1 peak

enables you to change the offset. A well known peak can be

shifted to an exact wavelength by entering values of

Old Peak 1

and

New Peak

Содержание Lambda 650









































































Результаты поиска

Содержание Lambda 650

Отзывы:

Бренды по названию

Популярные бренды

PerkinElmer Lambda 650, Руководство по оборудованию

Результаты поиска

Содержание Lambda 650

Отзывы:

Бренды по названию

Популярные бренды