PerkinElmer Lambda 650 Скачать руководство пользователя страница 17

Страница: 17 / 72

Lambda 650/850/950 Hardware Guide . 17

Electrical Safety

The instrument has been designed to protect the operator from potential electrical hazards.

This section describes some recommended electrical safety practices.

WARNING

Electrical Hazard

Any interruption of the protective conductor inside or outside the

instrument or disconnection of the protective conductor (earth/ground)

terminal is likely to make the instrument dangerous.

Intentional interruption is prohibited.

Lethal voltages are present in the instrument

•

Even with the power switch OFF, line power voltages can still be

present within the instrument.

•

When the instrument is connected to line power, terminals may be

live, and opening covers or removing parts (except those to which

access can be gained without the use of a tool) is likely to expose

live parts.

•

Capacitors inside the instrument may still be charged even if the

instrument has been disconnected from all voltage sources.

Electrical Protection

Insulation: Class I as defined in IEC 61010-1.

Installation Category: The instruments are able to withstand transient overvoltage according

to Installation Category II as defined in IEC 61010-1 and IEC 664.

Pollution Degree: The equipment will operate safely in environments that contain non-

conductive foreign matter and condensation up to Pollution Degree 2 as defined in IEC

61010-1 and IEC 664.

Electrical Safety Issues

To ensure satisfactory and safe operation of the instrument, it is essential that the

green/yellow lead of the line power cord is connected to true electrical earth (ground).

If any part of the instrument is not installed by a PerkinElmer service representative, make

sure that the line power plug is wired correctly:

Cord Lead Colors

Terminal

International USA

Live Brown

Black

Neutral Blue White

Protective Conductor

(earth/ground)

Green/Yellow Green

Содержание Lambda 650









































































Результаты поиска

Содержание Lambda 650

Отзывы:

Бренды по названию

Популярные бренды

PerkinElmer Lambda 650, Руководство по оборудованию

Результаты поиска

Содержание Lambda 650

Отзывы:

Бренды по названию

Популярные бренды