manualshive.com logo in svg

PerkinElmer Lambda 650, Руководство по оборудованию

Поделиться
Скачать
PerkinElmer Lambda 650 Скачать руководство пользователя страница 48

48 . Using the Instrument 

 

  The cell holder only fits one way round. 

 

Figure 14 Lambda 650/850/950 Sample Compartment Baseplate 

5.

 

Move the milled posts a little to locate the threaded holes in the baseplate, and then 

tighten the milled posts. 
You can lead tubes and connecting cables for accessories into the sample compartment 

through either the tube ports, located at the front of the sample compartment, or the 
opening located at the left rear of the sample compartment under the cover plate. 
When not in use, you should always insert the caps into the tube ports and keep the 

cover plate fixed in place. 
The cover plate is fixed in place by a retaining screw. 

Aligning the Single-cell Holder 

Coarse alignment of the single cell holder is carried out as follows: 

1.

 

Open the sample compartment cover. 

2.

 

Fill cells with a low-absorbing solvent (deionized water or ethanol). 

3.

 

Insert one cell into the sample cell holder and one into the reference cell holder. 
Make certain that the cell is pushed down fully. 

NOTE: 

  The alignment procedure is for a given cell in a given holder. After alignment, the cell should 

always be used in the same holder. 

4.

 

From The UV WinLab Explorer, select the instrument you are using and select 

Manual 

Control

 from the Tools menu. 

5.

 

From the Manual Control window, select 

Data Collection

 in the treelist and then select 

Alignment Mode

 on the page. 

6.

 

Block the sample and reference beam windows on the right side of the sample 

compartment with a card to prevent white light from saturating the detector. 

Cover Plate 

Sample Holder 
and Plinth

Drain Hole 

Locating Pin 

Retaining Screw 

Tube Ports 

Содержание Lambda 650









































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды