PerkinElmer Lambda 650 Скачать руководство пользователя страница 21

Страница: 21 / 72

Lambda 650/850/950 Hardware Guide . 21

Fuses

WARNING

Electrical hazard

To prevent potential injury to yourself and damage to the instrument,

switch OFF all instruments in the system and disconnect them from the

line power supply before you alter, or make any new, electrical

connections.

The fuses are located in a fuse holder at the rear of the instrument, as shown in Figure 3.

Figure 3 Rear view, fuse holder

Switch off the instrument and remove the line power cord from the electrical supply.

Squeeze in and lever out the two lugs at each side of the fuse holder one at a time
using a flat-headed screwdriver

Gently pull out the fuse holder.

Figure 4 Removing the fuse holder

Replace the fuses with new ones of the same type and rating (3.15 A time delay).

NOTE:

The module has two fuses and you should always replace both at the same time, even if only

one blew, as the other may have been weakened.

Replace the fuse holder by aligning the lug at the bottom of the fuse holder with the

slot in the socket and then pushing the holder into place.
A click is heard as each lug snaps into place.

NOTE:

If you use the correct fuses but the instrument still does not work correctly, or the fuses

blow repeatedly, contact your PerkinElmer office or representative.

Fuse Holder

Содержание Lambda 650









































































Результаты поиска

Содержание Lambda 650

Отзывы:

Бренды по названию

Популярные бренды

PerkinElmer Lambda 650, Руководство по оборудованию

Результаты поиска

Содержание Lambda 650

Отзывы:

Бренды по названию

Популярные бренды